Davo at 13:49, 26 June 2020

2020-06-26T13:49:55Z

← Older revision		Revision as of 13:49, 26 June 2020
Line 5:		Line 5:
	\|}		\|}

	The RSD-30 is a refrigerated (or, technically, heated) version of our [[SDS]]-30 extruder for low viscosity emulsions which print at temperatures down to ~~20C~~ below ambient.		The RSD-30 is a refrigerated (or, technically, heated) version of our [[SDS]]-30 extruder for low viscosity emulsions which print at temperatures down to 20°C below ambient.

	[[File:RSD-30.jpg\|200px\|left\|RSD-30]]		[[File:RSD-30.jpg\|200px\|left\|RSD-30]]

Davo: Created page with "Category:Hardware Category:Cold_Flow {| align="right" | TOC |} The RSD-30 is a refrigerated (or, technically, heated) version of our SDS-30 extruder for low v..."

2020-06-26T13:48:11Z

Created page with "Category:Hardware Category:Cold_Flow {| align="right" | __TOC__ |} The RSD-30 is a refrigerated (or, technically, heated) version of our SDS-30 extruder for low v..."

New page

[[Category:Hardware]]
[[Category:Cold_Flow]]
{| align="right"
| __TOC__
|}

The RSD-30 is a refrigerated (or, technically, heated) version of our [[SDS]]-30 extruder for low viscosity emulsions which print at temperatures down to 20C below ambient.

[[File:RSD-30.jpg|200px|left|RSD-30]]

This includes the following materials:

<div style="column-count:3;-moz-column-count:3;-webkit-column-count:3">
*Liquids
*Gels
*Emulsions
</div>

== Videos ==

# Overview of the head:
## [[File:Yt.png]] [https://www.youtube.com/watch?v=S3qw8dAWeNo Introducing the RSD-30]
# Installing the RSD Head:
## [[File:Yt.png]] [https://www.youtube.com/watch?v=dgfeoLZNW6c Installing the RSD Head on your printer]

== Description ==

The RSD heads accept 30cc BD plastic syringe reservoirs] with luer fittings. Industry standard luer tips or needles are available from a variety of sources.

== UV Crosslinking ==

All of our reservoir-based heads can take a [[UV_Array|UV Array]], mounted around the nozzle, or a [[UVP|UV Pen]], mounted in another tool position.

The [[UV_Array|UV Arrays]] are lower power, and available in 280, 310, 365, 405, or 450 nm.

The [[UVP|UV Pens]] are higher power, and available in 365, 405, or 450nm.

== Syringes ==

The RSD-30 takes the 30cc BD model 302832 syringe, available from many sources including [https://mms.mckesson.com/product/811979/Becton-Dickinson-302832 McKesson] and [https://www.vitalitymedical.com/30-ml-syringes-without-needle.html Vitality Medical].

== Loading the Head onto the Printer ==

As with all Hyrel heads, the following process should be followed:

# Start with a level bed and Repetrel running and connected to the printer.
# Load the gibs on the Head into the gib slots on the Yoke from above and slide the head down into place; the last mm of travel should be done gently, ensuring that the electrical connector seats properly (firmly and completely) into the receiving connector.
# Ensure the LEDs on the print head are flashing - this means the Head is communicating with the Motion Controller.
# Tighten the thumbscrew in the rear, to prevent the head from moving relative to the Yoke.
# If the Head doesn't show up in Repetrel, press and release the RESET button on the front of the printer.
# Once the Head is shown in repetrel, proceed to setting your Z-Zero position.

With the RSD head, you must provide a cold (or hot) water source; please see the video at https://www.youtube.com/watch?v=dgfeoLZNW6c

== Loading material into the Head ==

Loading:

* Care should be taken to avoid air pockets, as this will introduce delay when starting and stopping material flow.
* The plunger adapter will need to be adjusted up or down to match the position of the plunger for the amount of material you have loaded; do this with the manual feed lever at the top left of the 103 hothead controller board. See videos, above.

Unloading:

* Unloading is the same process as loading, only in reverse. Tubes and nozzles should be cleaned thoroughly after use.

== Default Parameters ==

Default settings for all SDS series heads are shown on the [[Cold_and_Warm_Flow]] page.

== Adjustments ==

The only adjustments needed should be changes to the PRIME and UNPRIME settings, and will have to be dialed in based on how viscous and compressible your material is, and how narrow a nozzle or luer tip you are using.. In dialing in new settings, I usually double or half the settings for both STEPS and TIME, then make another print and reassess.

== Firmware ==

Please see the [[Downloads]] page for the current firmware for your heads and your version of Repetrel.

Note that the default for version 3 is _TUBES_35K.hex for standard use, or _TUBES_49V.hex with the Clench Valve. On version 4 and later, ALL heads take the same firmware.

== Maintenance ==

With disposable syringes and luer tips to prevent cross-contamination, very little maintenance is required on these heads. Ensure that your temperature control reservoir and supply are kept clean.

RSD - Revision history

Davo at 13:49, 26 June 2020

Davo: Created page with "Category:Hardware Category:Cold_Flow {| align="right" | __TOC__ |} The RSD-30 is a refrigerated (or, technically, heated) version of our SDS-30 extruder for low v..."

Davo: Created page with "Category:Hardware Category:Cold_Flow {| align="right" | TOC |} The RSD-30 is a refrigerated (or, technically, heated) version of our SDS-30 extruder for low v..."