Davo at 13:20, 23 June 2020

2020-06-23T13:20:49Z

← Older revision		Revision as of 13:20, 23 June 2020
Line 5:		Line 5:
	\|}		\|}

	~~The UVP is our UV Pen, available in 365, 405, or 450 nm wavelengths~~.		Please use personal protective equipment and follow your facility safety guidelines at all times.

			== Overview ==

	[[File:UVP.jpg\|250px\|left\|KR2]]		[[File:UVP.jpg\|250px\|left\|KR2]]

			The UV Pen is a flashlight-like light source, providing high-power light in the following wavelengths:

			* 365 nm
			* 405 nm
			* 450 nm

	This is typically used in conjunction with reservoir-based printing to provide UV photoinitiation of crosslinking in photocurable materials.		This is typically used in conjunction with reservoir-based printing to provide UV photoinitiation of crosslinking in photocurable materials.

Davo: Created page with "Category:Hardware Category:Warm_Flow {| align="right" | TOC |} The UVP is our UV Pen, available in 365, 405, or 450 nm wavelengths. File:UVP.jpg|250px|left|KR..."

2020-06-22T20:58:10Z

Created page with "Category:Hardware Category:Warm_Flow {| align="right" | __TOC__ |} The UVP is our UV Pen, available in 365, 405, or 450 nm wavelengths. File:UVP.jpg|250px|left|KR..."

New page

[[Category:Hardware]]
[[Category:Warm_Flow]]
{| align="right"
| __TOC__
|}

The UVP is our UV Pen, available in 365, 405, or 450 nm wavelengths.

[[File:UVP.jpg|250px|left|KR2]]

This is typically used in conjunction with reservoir-based printing to provide UV photoinitiation of crosslinking in photocurable materials.

== Description ==

The UVP provides user control of power and focus of this head, either tied to or entirely separate from other heads.

== Loading the Head onto the Printer ==

As with all Hyrel heads, the following process should be followed:

# Start with a level bed and Repetrel running and connected to the printer.
# Load the gibs on the Head into the gib slots on the Yoke from above and slide the head down into place; the last mm of travel should be done gently, ensuring that the electrical connector seats properly (firmly and completely) into the receiving connector.
# Ensure the LEDs on the print head are flashing - this means the Head is communicating with the Motion Controller.
# Tighten the thumbscrew in the rear, to prevent the head from moving relative to the Yoke.
# If the Head doesn't show up in Repetrel, press and release the RESET button on the front of the printer.
# Once the Head is shown in repetrel, proceed to setting your Z-Zero position for the primary head

== GCODE ==

Please see [[UV_and_Clench]] and [[Cloning_and_Mixing]] for details about how to incorporate use of the UVP in your gcode file, as we know of no slicing program that incorporates this functionality.

== Firmware ==

Please see the [[Downloads]] page for the current firmware for your heads and your version of Repetrel.

== Maintenance ==

Keep the head out of harm's way and the lens covered when not in use.

UVP - Revision history

Davo at 13:20, 23 June 2020

Davo: Created page with "Category:Hardware Category:Warm_Flow {| align="right" | __TOC__ |} The UVP is our UV Pen, available in 365, 405, or 450 nm wavelengths. File:UVP.jpg|250px|left|KR..."

Davo: Created page with "Category:Hardware Category:Warm_Flow {| align="right" | TOC |} The UVP is our UV Pen, available in 365, 405, or 450 nm wavelengths. File:UVP.jpg|250px|left|KR..."