Davo: Redirected page to Cold and Warm Flow

2016-11-08T12:03:54Z

← Older revision		Revision as of 12:03, 8 November 2016
Line 1:		Line 1:
	[[~~Category:Hardware~~]]		#redirect[[Cold_and_Warm_Flow]]
	~~[[Category:Warm_Flow]]~~
	~~{\| align="right"~~
	~~\| __TOC__~~
	\|}


	~~Warm Flow is our term for fluid or emulsified (non-filament-based) materials which are deposited at up to 150°C, with or without UV Crosslinking, depending on the head.~~

	PCL and other medium temperature material can be printed directly from Pellets the size of small peas. If you pulverize or powder your polymer, it is possible to pre-mix the material dry and test different alloys of plastics.

	~~==Materials for Warm Flow==~~

	The following materials can be printed from Warm Flow heads. Note that more viscous materials may not be suitable for plastic syringes or smaller luer tips, or may print more easily at higher temperatures.

	~~<div style="column-count:5;-moz-column-count:5;-webkit-column-count:5">~~
	*[[Adhesives]]
	*[[Fimo]]
	*[[Kato]]
	*[[Glue]]
	*[[PCL]]
	*[[Plasticine]]
	*[[Resins]]
	*[[Sculpey]]
	*[[Wax]]
	~~</div>~~

	~~==Heads for Warm Flow==~~

	~~Warm Flow is available through the following heads:~~

	~~<gallery>~~
	~~File:VOL-25.png\|[[VOL-25]]~~
	~~File:VCD-25.png\|[[VCD-25]]~~
	~~File:KRA-15.png\|[[KRA-15]]~~
	~~File:KCD-15.png\|[[KCD-15]]~~
	~~</gallery>~~

	~~The following table compares the properties of the various Warm Flow heads:~~

	~~{\| border="1" class="wikitable sortable" style="width: 85%;"~~
	~~\|+ Warm Flow Head Properties~~
	~~! style="width: 15%;" \| Head~~
	~~! style="width: 15%;" \| Max Temp~~
	~~! style="width: 15%;" \| Container~~
	~~! style="width: 15%;" \| Capacity~~
	~~! style="width: 15%;" \| Nozzle~~
	~~! style="width: 15%;" \| UV Crosslinking~~
	\|-
	~~! [[VOL-25]]~~
	~~\| 100°C~~
	~~\| Aluminum~~
	~~\| 25cc~~
	~~\| 1.5mm, 2.0mm, Luer~~
	~~\| No~~
	\|-
	~~! [[VCD-25]]~~
	~~\| 100°C~~
	~~\| Aluminum~~
	~~\| 25cc~~
	~~\| Luer~~
	~~\| Yes~~
	\|-
	~~! [[KRA-15]]~~
	~~\| 150°C~~
	~~\| Stainless~~
	~~\| 15cc~~
	~~\| 1.5mm, 2mm, Luer~~
	~~\| No~~
	\|-
	~~! [[KCD-15]]~~
	~~\| 150°C~~
	~~\| Stainless~~
	~~\| 15cc~~
	~~\| Luer~~
	~~\| Yes~~
	\|-
	\|}

Davo: Created page with "Category:Hardware Category:Warm_Flow {| align="right" | TOC |} Warm Flow is our term for fluid or emulsified (non-filament-based) materials which are deposited a..."

2016-07-06T14:46:56Z

Created page with "Category:Hardware Category:Warm_Flow {| align="right" | __TOC__ |} Warm Flow is our term for fluid or emulsified (non-filament-based) materials which are deposited a..."

New page

[[Category:Hardware]]
[[Category:Warm_Flow]]
{| align="right"
| __TOC__
|}

Warm Flow is our term for fluid or emulsified (non-filament-based) materials which are deposited at up to 150°C, with or without UV Crosslinking, depending on the head.

PCL and other medium temperature material can be printed directly from Pellets the size of small peas. If you pulverize or powder your polymer, it is possible to pre-mix the material dry and test different alloys of plastics.

==Materials for Warm Flow==

The following materials can be printed from Warm Flow heads. Note that more viscous materials may not be suitable for plastic syringes or smaller luer tips, or may print more easily at higher temperatures.

<div style="column-count:5;-moz-column-count:5;-webkit-column-count:5">
*[[Adhesives]]
*[[Fimo]]
*[[Kato]]
*[[Glue]]
*[[PCL]]
*[[Plasticine]]
*[[Resins]]
*[[Sculpey]]
*[[Wax]]
</div>

==Heads for Warm Flow==

Warm Flow is available through the following heads:

<gallery>
File:VOL-25.png|[[VOL-25]]
File:VCD-25.png|[[VCD-25]]
File:KRA-15.png|[[KRA-15]]
File:KCD-15.png|[[KCD-15]]
</gallery>

The following table compares the properties of the various Warm Flow heads:

{| border="1" class="wikitable sortable" style="width: 85%;"
|+ Warm Flow Head Properties
! style="width: 15%;" | Head
! style="width: 15%;" | Max Temp
! style="width: 15%;" | Container
! style="width: 15%;" | Capacity
! style="width: 15%;" | Nozzle
! style="width: 15%;" | UV Crosslinking
|-
! [[VOL-25]]
| 100°C
| Aluminum
| 25cc
| 1.5mm, 2.0mm, Luer
| No
|-
! [[VCD-25]]
| 100°C
| Aluminum
| 25cc
| Luer
| Yes
|-
! [[KRA-15]]
| 150°C
| Stainless
| 15cc
| 1.5mm, 2mm, Luer
| No
|-
! [[KCD-15]]
| 150°C
| Stainless
| 15cc
| Luer
| Yes
|-
|}

Warm flow - Revision history

Davo: Redirected page to Cold and Warm Flow

Davo: Created page with "Category:Hardware Category:Warm_Flow {| align="right" | __TOC__ |} Warm Flow is our term for fluid or emulsified (non-filament-based) materials which are deposited a..."

Davo: Created page with "Category:Hardware Category:Warm_Flow {| align="right" | TOC |} Warm Flow is our term for fluid or emulsified (non-filament-based) materials which are deposited a..."