Emulsifiables

EMO-Type heads are for printing as follows:

• With pastes, gels, emulsifiables or waxes.
• At room or elevated temperatures.
• With or without UV Crosslining.
• With Hyrel Nozzles (1.5mm, 2mm) or Luer Tips.

These include the following:

EMO-Type Head Comparison

Temperature	Ambient	Up to 100°C	Up to 150°C
No Crosslinking	EMO-25 SDS-5, -10, -30, -60	VOL-25	KRA-15
With Crosslinking	COD-25 CSD-5, -10, -30, -60	VCD-25	KCD-15

So, what do these goofy designations actually stand for?

EMO: Emulsifiables at Room Temperature

COD: Emulsifiables T Room Temperature with Crosslink On Demand

VOL: Volcano: Heated (up to 100°C) Emulsifiables

VCD: Volcanic Crosslink on Demand

KRA: Krakatoa: Heated (up to 150°C) Emulsifiables

KCD: Krakatoic Crosslink on Demand

SDS: Syringe Dispensing System (uses disposable plastic syringes at room temperature)

CSD: Crosslinking Syringe Dispensing System

As of 16 Nov, the latest firmware is 32V, included with Repetrel 2.828.

Some settings for the EMO-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (1.6mm is default) AND what path width you sliced for. Temperature commands will be ignored by heads with no temperature control. Having said that, here are our default shipping settings:

EMO-Type Head Comparison

Settings	EMO, VOL, KRA, COD, VCD, KCD Heads (17mm Tubes, Various Gear Ratios)				SDS, CSD Heads (Various Tube Diameters, Standard Gear Ratios)
	19:1 Ratio	27:1 Ratio	51:1 Ratio	100:1 Ratio	SDS-5	SDS-10	SDS-30	5SDS-60
Material
Type	Plasticine	Plasticine	Plasticine	Plasticine	Plasticine	Plasticine	Plasticine	Plasticine
Color	(any)	(any)	(any)	(any)	(any)	(any)	(any)	(any)
Nozzle	1.600	1.600	1.600	1.600	1.600	1.600	1.600	1.600
Layer	300	300	300	300	300	300	300	300
Temp Info
Print Temp	30	30	30	30	0	0	0	0
Power Factor	100	100	100	100	100	100	100	100
Minimum	0	0	0	0	0	0	0	0
Maximum	0/100/150	0/100/150	0/100/150	0/100/150	0	0	0	0
Overrides
Pulses	1.600	2.300	4.700	8.500	TBD	TBD	TBD	TBD
Feed Rate %	1.000	1.000	1.000	1.000	TBD	TBD	TBD	TBD
Prime
Steps	500	700	900	2000	TBD	TBD	TBD	TBD
Rate	10,000	10,000	10,000	10,000	10,000	10,000	10,000	10,000
Dwell Time (ms)	100	100	110	120	TBD	TBD	TBD	TBD
Before Tool Change	1	1	1	1	1	1	1	1
Unprime
Steps	400	550	750	1600	TBD	TBD	TBD	TBD
Rate	10,000	10,000	10,000	10,000	10,000	10,000	10,000	10,000
Dwell Time (ms)	100	100	100	110	TBD	TBD	TBD	TBD
After Tool Change	1	1	1	1	1	1	1	1
Offsets
Clone Head	Off	Off	Off	Off	Off	Off	Off	Off
X	0,000	0,000	0,000	0,000	0,000	0,000	0,000	0,000
Y	0,000	0,000	0,000	0,000	0,000	0,000	0,000	0,000
Z	0,000	0,000	0,000	0,000	0,000	0,000	0,000	0,000
Head Info
Model	(varies)	(varies)	(varies)	(varies)	(varies)	(varies)	(varies)	(varies)
RTD Type	1 Meg	1 Meg	1 Meg	1 Meg	1 Meg	1 Meg	1 Meg	1 Meg
Motor Current	High	High	High	High	High	High	High	High
Step Mode	Sixteenth	Sixteenth	Sixteenth	Sixteenth	Sixteenth	Sixteenth	Sixteenth	Sixteenth