Emulsifiables

Overview

EMO-Type heads are for printing as follows:

• With pastes, gels, emulsifiables or waxes.
• At room or elevated temperatures.
• With or without UV Crosslining.
• With Hyrel Nozzles (1.5mm, 2mm) or Luer Tips.

These include the following:

EMO-Type Head Comparison

Temperature	Ambient	Up to 75°C	Up to 100°C	Up to 150°C
No Crosslinking	EMO-25 SDS-5, -10, -30, -60	VSD-5, -10, -30, -60	VOL-25	KRA-15
With Crosslinking	COD-25 CSD-5, -10, -30, -60	VCS-5, -10, -30, -60	VCD-25	KCD-15

So, what do these goofy designations actually stand for?

EMO: Emulsifiables at Room Temperature

COD: Emulsifiables T Room Temperature with Crosslink On Demand

VOL: Volcano: Heated (up to 100°C) Emulsifiables

VCD: Volcanic Crosslink on Demand

KRA: Krakatoa: Heated (up to 150°C) Emulsifiables

KCD: Krakatoic Crosslink on Demand

SDS: Syringe Dispensing System (uses disposable plastic syringes at room temperature)

CSD: Crosslinking Syringe Dispensing System

VSD: Volcanic Syringe Dispensing System

CVS: Crosslinking Volcanic Syringe Dispensing System

As of Sep 2016, the latest firmware is 32V, included with Repetrel 2.828.

Settings

Some settings for the EMO-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (1.6mm is default) AND what path width you sliced for. Temperature commands will be ignored by heads with no temperature control. Having said that, here are our default shipping settings:

EMO-Type Head Comparison

Settings	EMO, VOL, KRA, COD, VCD, KCD Heads (17mm Tubes, Various Gear Ratios)				SDS, CSD, VSD Heads (Various Tube Diameters, Standard Gear Ratios)
	19:1 Ratio	27:1 Ratio	51:1 Ratio	100:1 Ratio	SDS-5	SDS-10	SDS-30	SDS-60
Material
Type	Custom	Custom	Custom	Custom	Custom	Custom	Custom	Custom
Color	(any)	(any)	(any)	(any)	(any)	(any)	(any)	(any)
Nozzle	1.600	1.600	1.600	1.600	1.600	1.600	1.600	1.600
Layer	0.300	0.300	0.300	0.300	0.300	0.300	0.300	0.300
Temp Info
Print Temp	35	35	35	35	0	0	0	0
Power Factor	100	100	100	100	100	100	100	100
Minimum	0	0	0	0	0	0	0	0
Maximum	0/100/200	0/100/200	0/100/200	0/100/200	0	0	0	0
Overrides
Pulses	1.600	2.300	4.700	8.500	0.750	0.580*	0.225	0.150
Feed Rate %	1.000	1.000	1.000	1.000	1.000	1.000	1.000	1.000
Prime Please note that Prime values will vary greatly from those shown, depending on the compressibility of your material.
Steps	600	700	1000	4000	200	200	300	500
Rate	10,000	10,000	10,000	10,000	10,000	10,000	10,000	10,000
Dwell Time (ms)	100	100	110	120	100	100	100	100
Before Tool Change	1	1	1	1	1	1	1	1
Unprime Please note that Unprime values will vary greatly from those shown, depending on the compressibility of your material.
Steps	500	550	800	3500	160	160	225	400
Rate	10,000	10,000	10,000	10,000	10,000	10,000	10,000	10,000
Dwell Time (ms)	100	100	100	110	100	100	100	100
After Tool Change	1	1	1	1	1	1	1	1
Offsets
Clone Head	Off	Off	Off	Off	Off	Off	Off	Off
X	0,000	0,000	0,000	0,000	0,000	0,000	0,000	0,000
Y	0,000	0,000	0,000	0,000	0,000	0,000	0,000	0,000
Z	0,000	0,000	0,000	0,000	0,000	0,000	0,000	0,000
Head Info
Model	(varies)	(varies)	(varies)	(varies)	(varies)	(varies)	(varies)	(varies)
RTD Type	1k PLAT_RTD	1k PLAT_RTD	1k PLAT_RTD	1k PLAT_RTD	1k PLAT_RTD	1k PLAT_RTD	1k PLAT_RTD	1k PLAT_RTD
Motor Current	High	High	High	High	High	High	High	High
Step Mode	Sixteenth	Sixteenth	Sixteenth	Sixteenth	Sixteenth	Sixteenth	Sixteenth	Sixteenth
* Thanks to Yasmine at VT for the precise calculation.