Published Papers

Below is a list of research papers citing Hyrel equipment.

Research Papers Citing Hyrel Cold Flow

• Alginate Hydrogels for Bone Tissue Regeneration by Stephanie T. Bendtsen of The University of Connecticut
• Fabrication of Biomimetic Bone Grafts with Multi-Material 3D Printing by Nicholas Sears et. al., of the Biomedical Engineering Department of Texas A&M University.
• Nanoengineered Eggshell–Silver Tailored Copolyester Polymer Blend Film with Antimicrobial Properties by the Department of Materials Science and Engineering and the Department of Pathobiology, College of Veterinary Medicine of Tuskegee University
• Additive Manufacturing of Magnetic Components for Heterogeneous Integration by Dr. Y. Yan (and others), Virginia Tech
• Die-Less MIM-style Additive Manufacturing with Controlled Porosity: A Proof of Concept by the Department of Materials Science and Engineering of Lehigh University
• 3D Printed Energetics by the Weapons and Combat Systems Division of the Australian Department of Defense
• Development of 3D printed Ceramic scaffolds for Treatment of Segmental Bone Defects from The Biomaterials and Tissue Engineering Research Unit of the Aerospace, Mechanical and Mechatronic Engineering Department of The University of Sydney
• Graduate Abstract: Dynamic increase in matrix stiffness promotes invasive tumor phenotype in vivo from multiple organizations, at BioMaterials.org
• 3D Printing of High Porosity, Biodegradable Foams with Cure on Dispense - Presentation by Elizabeth Cosgriff-Hernández of Department of Biomedical Engineering, Texas A&M University
• Design Methodology and Materials for Additive Manufacturing of Magnetic Components - PhD Thesis of Y. Yan, Virginia Tech
• Bioprinting Defined Heterogeneous Cellular Microenvironments from The Biomaterials and Tissue Engineering Research Unit of the Aerospace, Mechanical and Mechatronic Engineering Department of The University of Sydney
• A Novel Approach to Integrating 3D/4D Printing and Stretchable Conductive Adhesive Technologies for High Frequency Packaging Applications
• Additive Manufacturing of Planar Inductor for Power Electronics Applications
• Bioactive Nanoengineered Hydrogels for Bone Tissue Engineering: A Growth-Factor-Free Approach in The American Chemical Society's ACS Nano
• Design and Fabrication of 3D Printed Scaffolds with a Mechanical Strength Comparable to Cortical Bone to Repair Large Bone Defects in Nature.com's Scientific Reports
• Emulsion Inks for 3D Printing of High Porosity Materials in the Macromolecular Journals

Research Papers Citing Hyrel Warm Flow

• Influence of Shear Thinning and Material Flow on Robotic Dispensing of PEG in in The American Chemical Society's ACS Nano

Research Papers Citing Hyrel Hot Flow

• Dynamical Majorana edge modes in a broad class of topological mechanical systems by The New Jersey Institute of Technology
• A Low-Cost, Single Platform, Hybrid Manufacturing System for RF Passives, The Institute of Electrical and Electronics Engineers, Incorporated (IEEE)
• Button-Shaped RFID Tag Combining Three-Dimensional and Inkjet Printing Technologies, The IET Digital Library.
• Demonstration and Characterization of Fully 3D-printed RF Structures, The Institute of Electrical and Electronics Engineers, Incorporated (IEEE)
• Infill Dependent 3D-Printed Material Based on NinjaFlex Filament for Antenna Applications, The Institute of Electrical and Electronics Engineers, Incorporated (IEEE)
• A Novel Strain Sensor Based on 3D Printing Technology and 3D Antenna Design, The Institute of Electrical and Electronics Engineers, Incorporated (IEEE)
• A Novel 3-D Printed Loop Antenna Using Flexible NinjaFlex Material for Wearable and IoT Applications, The Institute of Electrical and Electronics Engineers, Incorporated (IEEE)
• RF Characterization of 3D Printed Flexible Materials - NinjaFlex Filaments, The European Microwave Association (EuMA)
• Nano-Material Based Flexible Radio Frequency Sensors for Wearable Health and Environment Monitoring: Designs and Prototypes Utilizing 3D/Inkjet Printing Technologies, A Dissertation Presented to The Academic Faculty of The School of Electrical and Computer Engineering at Georgia Tech