Difference between revisions of "Emulsifiables"

From Hyrel3D
Jump to navigation Jump to search
Line 34: Line 34:
|KCD-15
|KCD-15
|}
|}
So, what do these goofy designations actually stand for?
:EMO: Emulsifiables at Room Temperature
:COD: Emulsifiables T Room Temperature with Crosslink On Demand
:VOL: Volcano: Heated (up to 100°C) Emulsifiables
:VCD: Volcanic Crosslink on Demand
:KRA: Krakatoa: Heated (up to 150°C) Emulsifiables
:KCD: Krakatoic Crosslink on Demand
:SDS: Syringe Dispensing System (uses disposable plastic syringes at room temperature)
:CSD: Crosslinking Syringe Dispensing System


As of 16 Nov, the latest firmware is 32V, included with Repetrel 2.828.
As of 16 Nov, the latest firmware is 32V, included with Repetrel 2.828.

Revision as of 15:06, 8 December 2015

EMO-Type heads are for printing as follows:

  • With pastes, gels, emulsifiables or waxes.
  • At room or elevated temperatures.
  • With or without UV Crosslining.
  • With Hyrel Nozzles (1.5mm, 2mm) or Luer Tips.

These include the following:

EMO-Type Head Comparison
Temperature Ambient Up to 100°C Up to 150°C
No Crosslinking EMO-25

SDS-5, -10, -30, -60

VOL-25 KRA-15
With Crosslinking COD-25

CSD-5, -10, -30, -60

VCD-25 KCD-15

So, what do these goofy designations actually stand for?

EMO: Emulsifiables at Room Temperature
COD: Emulsifiables T Room Temperature with Crosslink On Demand
VOL: Volcano: Heated (up to 100°C) Emulsifiables
VCD: Volcanic Crosslink on Demand
KRA: Krakatoa: Heated (up to 150°C) Emulsifiables
KCD: Krakatoic Crosslink on Demand
SDS: Syringe Dispensing System (uses disposable plastic syringes at room temperature)
CSD: Crosslinking Syringe Dispensing System

As of 16 Nov, the latest firmware is 32V, included with Repetrel 2.828.

Some settings for the EMO-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (1.6mm is default) AND what path width you sliced for. Temperature commands will be ignored by heads with no temperature control. Having said that, here are our default shipping settings:

EMO-Type Head Comparison
Settings EMO, VOL, KRA, COD, VCD, KCD Heads (17mm Tubes) SDS, CSD Heads (Various Tube Diameters)
19:1 Ratio 27:1 Ratio 51:1 Ratio 100:1 Ratio SDS-5 SDS-10 SDS-30 5SDS-60
Material
Type (any) (any) (any) (any) (any) (any) (any) (any)
Color (any) (any) (any) (any) (any) (any) (any) (any)
Nozzle 1.600 1.600 1.600 1.600 1.600 1.600 1.600 1.600
Layer (any) (any) (any) (any) (any) (any) (any) (any)
Temp Info
Print Temp 30 30 30 30 30 30 30 30
Power Factor 100 100 100 100 100 100 100 100
Minimum (any) (any) (any) (any) (any) (any) (any) (any)
Maximum (any) (any) (any) (any) (any) (any) (any) (any)
Overrides
Pulses 1.600 2.300 4.700 8.750 TBD TBD TBD TBD
Feed Rate % 1.000 1.000 1.000 1.000 TBD TBD TBD TBD
Prime
Steps 500 700 900 2000 TBD TBD TBD TBD
Rate 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000
Dwell Time (ms) 100 100 110 120 TBD TBD TBD TBD
Before Tool Change 1 1 1 1 1 1 1 1
Unprime
Steps 400 550 750 1600 TBD TBD TBD TBD
Rate 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000
Dwell Time (ms) 100 100 100 110 TBD TBD TBD TBD
After Tool Change 1 1 1 1 1 1 1 1
Offsets
Clone Head Off Off Off Off Off Off Off Off
X 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000
Y 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000
Z 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000
Head Info
Model (varies) (varies) (varies) (varies) (varies) (varies) (varies) (varies)
RTD Type 1 Meg 1 Meg 1 Meg 1 Meg 1 Meg 1 Meg 1 Meg 1 Meg
Motor Current High High High High High High High High
Step Mode Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth