Difference between revisions of "Main Page"

From Hyrel3D
Jump to navigation Jump to search
Line 127: Line 127:


Warm Flow means fluid (non-filament-based) materials which are deposited at up to 100°C, with or without UV Crosslinking.
Warm Flow means fluid (non-filament-based) materials which are deposited at up to 100°C, with or without UV Crosslinking.
PCL and other medium temperature material can be printed directly from Pellets the size of small peas. If you pulverize or powder your polymer, it is possible to pre-mix the material dry and test different alloys of plastics.


===Materials, Warm Flow===
===Materials, Warm Flow===
Line 183: Line 185:
|-
|-
|}
|}


==Hot Flow==
==Hot Flow==

Revision as of 18:04, 28 January 2016

With literally thousands of materials to print on the Hyrel Printer, we have broken down the list of materials into logical groups based on their printing temperature and type of head used to print them.

If you are planning on using the heads which photoinitiate crosslinking, make sure you specify the correct wavelength of LED for your material.

A standard material printing data sheet has been created for materials that have been internally tested; you can access this data by clicking on the material name below.

Printers

As of Jan, 2016, Hyrel Printers are available in two models: Engines and Systems.

Engines and Systems

Engines are open-air models. Detailed information is on the Engines page. Systems are enclosed models. Detailed information is on the Systems page. Both models feature over 200x200x200mm of build volume. Each model can take up to four of our modular heads detailed below. Build plates will get to between 70°C and 85°C, depending on ambient temperature.

The Next Big Thing

Information not yet available. :)

Cold Flow

Cold Flow means fluid (non-filament-based) materials which are deposited at room temperature, with or without UV Crosslinking.

Materials, Cold Flow

Heads, Cold Flow

Cold Flow Head Properties
Head Container Capacity Nozzle UV Crosslinking
EMO-25 Aluminum 25cc 1.5mm, 2.0mm, Luer No
COD-25 Aluminum 25cc Luer Yes
SDS-5 Syringe 05cc Luer No
CSD-5 Syringe 05cc Luer Yes
SDS-10 Syringe 10cc Luer No
CSD-10 Syringe 10cc Luer Yes
SDS-30 Syringe 30cc Luer No
CSD-30 Syringe 30cc Luer Yes
SDS-60 Syringe 60cc Luer No
CSD-60 Syringe 60cc Luer Yes


Research Papers Citing Hyrel Cold Flow

Warm Flow

Warm Flow means fluid (non-filament-based) materials which are deposited at up to 100°C, with or without UV Crosslinking.

PCL and other medium temperature material can be printed directly from Pellets the size of small peas. If you pulverize or powder your polymer, it is possible to pre-mix the material dry and test different alloys of plastics.

Materials, Warm Flow

Note that some materials (like Fimo, Plasticine and Sculpey) flow more freely when slightly above room temperature, and perhaps too freely at higher temperatures.

Heads, Warm Flow

Cold Flow Head Properties
Head Max Temp Container Capacity Nozzle UV Crosslinking
VOL-25 100°C Aluminum 25cc 1.5mm, 2.0mm, Luer No
VCD-25 100°C Aluminum 25cc Luer Yes
KRA-15 150°C Stainless 15cc 1.5mm, 2mm, Luer No
KCD-15 150°C Stainless 15cc Luer Yes

Hot Flow

Hot Flow means 1.75mm diameter, filament-based materials which are deposited at up to 250°C, with

Materials, Hot Flow

Heads, Hot Flow

Cold Flow Head Properties
Head Min Temp Max Temp Filament Type Nozzle Recommended For
MK1-250 150°C 250°C Standard .35mm, .50mm, .75mm, 1.0mm ABS, LayBrick, LayWood, Nylon PC, PET, PETG, PETT, PLA, PP, PVA, T-Glase
MK2-250 150°C 250°C Flexible .35mm, .50mm, .75mm, 1.0mm BendLay, FilaFlex, Flex45, NinjaFlex, PlastInk Rubber
MK1-450 250°C 450°C Engineering .50mm PC, PEEK


Research Papers Citing Hyrel Hot Flow

Retrieved from "https://hyrel3d.in/wiki/index.php?title=Main_Page&oldid=413"