Difference between revisions of "Instructions"
Jump to navigation
Jump to search
Line 82: | Line 82: | ||
# [[File:Yt.png]] Session 3C - Slicing for Second Head Support | # [[File:Yt.png]] Session 3C - Slicing for Second Head Support | ||
# [[File:Yt.png]] Session 3D - Printing with Second Head Support | # [[File:Yt.png]] Session 3D - Printing with Second Head Support | ||
# [[File:Yt.png]] Session 3D - [https://www.youtube.com/watch?v=cuRcIE-Jbyc Clone or Parallel Printing] | |||
== '''Advanced Printing: Multiple STLs, Multiple Heads''' == | == '''Advanced Printing: Multiple STLs, Multiple Heads''' == |
Revision as of 12:31, 14 November 2016
Here are some step by step instructions for learning how to use your Hyrel 3D Printer.
Please also see the Videos page.
Before You Get Started
Unboxing Your Printer:
Basic Printing: One STL and One Head
First Training Session
Overview, Tramming, Printing with an Emulsifiable:
- First Training Session PDF
- Session 1A: Hardware and Software Overview Video
- Session 1B: Communications and Tramming Video
- Session 1C: Setting Z-Zero and Emulsifiable Print Video
Additional Emulsifiable Videos
- EMO Series Printing Tips
- Loading the EMO-25
- More Loading the EMO-25
- Loading the VCD Head
- Loading the SDS Head
- Loading the SDS Head with RTV
- Loading and Printing with the EMO-25
Second Training Session
CAD Modeling, Healing, Positioning, and Printing with Filament:
- Second Training Session PDF
- Session 2A: Simple CAD Modeling in FreeCAD Video
- Session 2B: Healing an STL in MeshLab Video
- Session 2C: Positioning, Scaling, and Rotating your STL Video
- Session 2D: Editing Slic3r Recipes Video
- Session 2E: Slicing your STL and Viewing your GCODE Video
- Session 2F: Loading and Printing with Filaments Video
Additional Filament Videos
- General MK Series:
- MK1-250 Extruder for Standard Filaments:
- MK2-250 Extruder for Flexible Filaments:
- MK1-450 Extruder for High-Temperature Filaments:
- Overview
- Loading and Printing
Additional Basic Printing Instructions
- Repetrel 3D Printing Basics
- Tramming your Bed: Systems and Engines, 2015 and later
- Tramming your Bed: Earlier Systems and Engines
Intermediate Printing: One STL, Multiple Heads
Z Level Adjustment for Dual Heads
- Session 3A - Setting Two Heads to Z-Zero
- Session 3B - Calibrating Offsets Between Two Heads
- Session 3C - Slicing for Second Head Support
- Session 3D - Printing with Second Head Support
- Session 3D - Clone or Parallel Printing
Advanced Printing: Multiple STLs, Multiple Heads
Troubleshooting, Maintenance and Tuning
- Establishing Connectivity between PC and Printer: https://www.youtube.com/watch?v=RlJqdhtpB6Q
- Table Arm Block Adjustment for bed twist about the X or Y axes: https://www.youtube.com/watch?v=ImMo3V1D70w
- Replacing the Heated Build Platform: https://www.youtube.com/watch?v=FkJT3ILlAHw
- NEW Tramming the heated build platform and setting Z-Zero: https://www.youtube.com/watch?v=lK_x0M8p9Ew
- Updating Slic3r Settings: https://www.youtube.com/watch?v=A0I6Xu9Tlvc
- Multi-Head Calibration Guide: https://www.youtube.com/watch?v=IQscrgv6uaQ
- To replace your Tablet Interface Board; also to run from an external PC (start at 6:24): https://www.youtube.com/watch?v=b583I7AlGJI
- Adjusting the X-Arm: https://www.youtube.com/watch?v=0gFX6Mh-ths
- Tightening the X Belt: https://www.youtube.com/watch?v=4GYWfMrs0F8
- Adjusting the Y-Arm: https://www.youtube.com/watch?v=LZd0ecogGlQ
- Tightening the Y Belt: https://www.youtube.com/watch?v=IkgviAGep-c
- Replacing your Power Supply https://www.youtube.com/watch?v=Zl1sqy6PWx8
- Replacing the heated build platform: https://www.youtube.com/watch?v=ed8ZqZLsTJ8
- Replacing the 4A fuses (1206 package) on the yoke: https://www.youtube.com/watch?v=EosKDe-SyUI
- Updating the 103 HotHead / HotBed Controllers: https://www.youtube.com/watch?v=yM8QMZBTb4o
- Replacing the 103 HotHead Controller: https://www.youtube.com/watch?v=XKCEkKSolZc
- Updating the 407 Motion Controller: https://www.youtube.com/watch?v=cFAFRkpLmww
- Changing the Print Head PCB: https://www.youtube.com/watch?v=XKCEkKSolZc
- Changing the Main I/O Board: https://www.youtube.com/watch?v=66S9XJ-KeU8
- Configuring the USB-B to run from another coputer: https://www.youtube.com/watch?v=uPqr4S0WC3Q
- Assembling the new PEEK Fan Nozzle: https://www.youtube.com/watch?v=ysO8oAzFwC4