Reservoir Heads

Cold Flow is our term for fluid or emulsified (non-filament-based) materials which are deposited at room temperature, with or without UV Crosslinking.

Warm Flow is our term for fluid or emulsified (non-filament-based) materials which are deposited at elevated temperatures, with or without UV Crosslinking.

Materials for Cold and Warm Flow

Cold and Warm Flow heads are for printing as follows:

• With pastes, gels, emulsifiables or waxes.
• At room or elevated temperatures.
• With or without UV Crosslining.
• With Hyrel Nozzles (1.5mm, 2mm) or Luer Tips.

The following materials can be printed from Cold Flow heads. Note that more viscous materials may not be suitable for plastic syringes or smaller luer tips.

• 3P Quick Cure Clay
• Adhesives
• Clay, Generic
• Epoxy, Two-part
• Fimo
• Glue
• Kato
• Metal Clay, including Precious Metal Clay (PMC)
• Modeling Clay
• PEG PolyEthylene Glycol
• Porcelain
• Plasticine
• Play-Doh
• Resins
• RTV Silicone
• Sculpey
• Sugru

The following materials can be printed from Warm Flow heads. Note that more viscous materials may not be suitable for plastic syringes or smaller luer tips, or may print more easily at higher temperatures.

• Adhesives
• Fimo
• Kato
• Glue
• PCL
• Plasticine
• Resins
• Sculpey
• Wax

Heads for Cold and Warm Flow

Cold Flow is available through the following heads:

• 

  EMO-25

• 

  COD-25

• 

  SDS-5, SDS-10,
  SDS-30, SDS-60

• 

  CSD-5, CSD-10,
  CSD-30, CSD-60

• SMH-2 Static Mixing Head

Warm Flow is available through the following heads:

• 

  VOL-25

• 

  VOL-25 with COD

• 

  KRA-15

• 

  KRA-15 with COD

• Overview of the EMO Heads
• Overview of the SDS Heads
• Overview of the VOL Heads
• Overview of the KRA Heads
• Overview of the SMH-2 Head
• Please see our Data Sheets as well.

EMO-Type Head Comparison

Temperature >	Down to 0°C >	Ambient	Up to 75°C	Up to 100°C	Up to 180°C	Up to 250°C
Crosslinking Optional	RSD-30	EMO-25 SDS-5, -10, SDS-30, -60 SMH-2	HSD-30 VOL-25	HSD-10	KRA-15 KR2-15	TAM-15

Note, RSD-30 will take you about 20C below ambient.

So, what do these goofy designations actually stand for?

EMO: Emulsifiables at Room Temperature - Low to Medium Viscosity

COD: Emulsifiables T Room Temperature with Crosslink On Demand - Low to Medium Viscosity

VOL: Volcano: Heated (up to 100°C) Emulsifiables - Low to Medium Viscosity

KR2: Krakatoa v2: a more robust KRA head with a double gasketed plunger hotter, more viscous Emulsifiables - Very High Viscosity

TAM: Tambora: Heated (up to 300°C) Emulsifiables - High Viscosity

SDS: Syringe Dispensing System (uses disposable plastic syringes at room temperature) - Low Viscosity

HSD: Heated (formerly Volcanic) Syringe Dispensing System - Low to Medium Viscosity

RSD: Refrigerated Syringe Dispensing System - Low to Medium Viscosity

DSD: Dual Syringe Dispenser, dispensing two-part mixtures at a fixed ratio - Low to Medium Viscosity

SMH: Static Mixing Head, blending your ratio of material through a baffled nozzle - Low to Medium Viscosity

As of May, 2018, for S30 and ESR, the latest firmware is 32V, included with Repetrel 2.865; for EHR and Hydras, the latest firmware is the same, with Repetrel 3.075_A.

Research Papers Citing Hyrel Cold and Warm Flow

These are now listed by year here.

Firmware Versions for Cold and Warm Flow Heads

As of May, 2018, the following versions should be used for Repetrel versions 2.x and 3.x:

Use _TUBES_35K.hex :

• For all emulsion heads performing prime/unprime actions.
• For all emulsion heads with COD LED activity on constantly.

Use _TUBES_49V.hex :

• For all emulsion heads using Clench Valves instead of prime/unprime actions.
• For all emulsion heads using COD LED activity tied to printing moves only.

Use _FIL_250_PLAT_1A.hex :

• For heated emulsions heads which don't seem to reach max temperature.

Settings for Cold and Warm Flow Heads

Non-Hydra units shipping through spring 2017 ship with Repetrel version 2.x. Hydra units, and other units shipping as of summer 2017 will have version 3.x, and should consult the version 3.x tables, below. All units should be upgraded to 3.x when it is available. If you run a head with v2 settings on a v3 install, the background will flash red; please make the changes below:

Values for versions 1.x and 2.x will be inicated in RED.

Values for version 3.x will be inicated in BLUE.

Values for version 4.x will be inicated in GREEN.

Note that you must flash these settings to the head to make them the new default.

Some settings for the EMO-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (1.6mm is default) AND what path width you sliced for. Temperature commands will be ignored by heads with no temperature control. Having said that, below are our default shipping settings:

METAL Reservoir Heads

Settings for Cold and Warm Flow Heads with METAL Reservoirs

Settings	EMO, VOL, KRA, COD, VCD, KCD Heads and New KR2 and TAM (17mm Tubes, Various Gear Ratios)
	19:1 Ratio	27:1 Ratio	51:1 Ratio	100:1 KRA & EMO-XT	100:1 KR2, TAM
Material
Type	Custom	Custom	Custom	Custom	Custom
Color	(any)	(any)	(any)	(any)	(any)
Nozzle	1.600	1.600	1.600	1.600	1.600
Layer	0.300	0.300	0.300	0.300	0.300
Temp Info
Print Temp	35	35	35	35	35
Power Factor	100	100	100	100	100
Minimum	0	0	0	0	0
Maximum	0	0/80	0/80	0/80/150	0/80/150/250
Overrides
Pulses	1.6 / 176 / 176	2.3 / 275 / 275	4.8 / 517 / 517	9.0 / 1,000 / 1,000	15 / 600 / 600
Multiplier	1	1	1	1	1 / 2 / 2
Prime
Steps	7000	6000	1000	3000	6000
Rate	10,000	10,000	10,000	10,000	10,000
Dwell Time (ms)	600	500	100	300	600
Before Tool Change	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a
Unprime
Steps	7000	6000	1000	3000	6000
Rate	10,000	10,000	10,000	10,000	10,000
Dwell Time	600 / -600 / -600	500 / -500 / -500	100 / -100 / -100	300 / -300 / -300	500 / -500 / -500
After Tool Change	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a
Offsets
Clone Head	Off	Off	Off	Off	Off
X	0,000	0,000	0,000	0,000	0,000
Y	0,000	0,000	0,000	0,000	0,000
Z	0,000	0,000	0,000	0,000	0,000
Head Info
Model	(varies)	(varies)	(varies)	(varies)	(varies)
PCB Type	n/a / n/a / 4988/160J	n/a / n/a / 4988/160J	n/a / n/a / 4988/160J	n/a / n/a / 4988/160J	n/a / n/a / 4988/160J
RTD Type	1k PLAT_RTD	1k PLAT_RTD	1k PLAT_RTD	1k PLAT_RTD	1k PLAT_RTD
Motor Current	High / High / n/a	High / High / n/a	High / High / n/a	High / High / n/a	High / High / n/a
Step Mode	16th / 16th / n/a	16th / 16th / n/a	16th / 16th / n/a	16th / 16th / n/a	16th / 16th / n/a
Plot Settings	(any)	(any)	(any)	(any)	(any)
Motor Settings
Step Mode	n/a / n/a / 16th	n/a / n/a / 16th	n/a / n/a / 16th	n/a / n/a / 16th	n/a / n/a / 16th
Motor Current	n/a / n/a / Normal	n/a / n/a / Normal	n/a / n/a / Normal	n/a / n/a / Normal	n/a / n/a / Normal
Max Jog Rate	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 7,500	n/a / n/a / 15,000	n/a / n/a / 15,000
Rot Speed	n/a / n/a / 7,500	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 15,000	n/a / n/a / 15,000
Settings	19:1 Ratio	27:1 Ratio	51:1 Ratio	100:1 KRA & EMO-XT	100:1 KR2, TAM

PLASTIC Reservoir Heads

Settings for Cold and Warm Flow Heads with PLASTIC Reservoirs

Settings	SDS, HSD, and RSD Heads (with or without COD) (Various Tube Diameters, Standard Gear Ratios)						DSD-50 (1:1)	Special (with or without COD)
	1cc ET	5cc	10cc	30cc	60cc	150cc	DSD-50	HSD-10-Ardes	SDS-30XT	SDS-60XT
Material
Type	Custom	Custom	Custom	Custom	Custom	Custom	Custom	Custom	Custom	Custom
Color	(any)	(any)	(any)	(any)	(any)	(any)	(any)	(any)	(any)	(any)
Nozzle	1.600	1.600	1.600	1.600	1.600	4.00	1.600	1.600	1.600	1.6000
Layer	0.300	0.300	0.300	0.300	0.300	0.300	0.300	0.300	0.300	0.300
Temp Info
Print Temp	0	0	0	0	0	0	0	35	0	0
Power Factor	100	100	100	100	100	100	100	100	100	100
Minimum	0	0	0	0	0	0	0	0	0	0
Maximum	0	0	0	0; 75 for HSD	0	0	0	130	0	0
Overrides
Pulses	5.8 / 610 / 610	0.75 / 81 / 81	0.58 / 62.5 / 62.5	0.225 / 30 / 30	0.15 / 20 / 20	? / 22 / 22	0.135 / 20 / 20	? / 900 / 900	? / 86 / 86	? / 25 / 25
Multiplier	1.000	1.000	1.000	1.000	1.000	1.000	1.000	1 / 2 / 2	1.000	1.000
Prime
Steps	7500	1500	3000	2250	1500	1500	1	9000	1125	1500
Rate	10,000	10,000	10,000	10,000	10,000	10,000	10,000	10,000	10,000	10,000
Dwell Time (ms)	800	150	300	300	300	300	100	900	300	300
Before Tool Change	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a
Unprime
Steps	7500	1500	3000	2250	1500	1500	1	9000	1125	1500
Rate	10,000	10,000	10,000	10,000	10,000	10,000	10,000	10,000	10,000	10,000
Dwell Time	800 / -800 / -800	300 / -300 / -300	300 / -300 / -300	300 / -300 / -300	300 / -300 / -300	300 / -300 / -300	1 / -1 / -1	900 / -900 / -900	300 / -300 / -300	300 / -300 / -300
After Tool Change	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a	2 / n/a / n/a
Offsets
Clone Head	Off	Off	Off	Off	Off	Off	Off	Off	Off	Off
X	0,000	0,000	0,000	0,000	0,000	0,000	0,000	0,000	0,000	0,000
Y	0,000	0,000	0,000	0,000	0,000	0,000	0,000	0,000	0,000	0,000
Z	0,000	0,000	0,000	0,000	0,000	0,000	0,000	0,000	0,000	0,000
Head Info
Model	(varies)	(varies)	(varies)	(varies)	(varies)	(varies)	(varies)	(varies)	(varies)	(varies)
PCB Type	n/a / n/a / 4988/160J	n/a / n/a / 4988/160J	n/a / n/a / 4988/160J	n/a / n/a / 4988/160J	n/a / n/a / 4988/160J	n/a / n/a / 4988/160J	n/a / n/a / 4988/160J	n/a / n/a / 4988/160J	n/a / n/a / 4988/160J	n/a / n/a / 4988/160J
RTD Type	None	None	None	None; varies for HSD, RSD	None	None	None	1k_PLAT_RTD	None	None
Motor Current	High / High / n/a	High / High / n/a	High / High / n/a	High / High / n/a	High / High / n/a	High / High / n/a	High / High / n/a	High / High / n/a	High / High / n/a	High / High / n/a
Step Mode	16th / 16th / n/a	16th / 16th / n/a	16th / 16th / n/a	16th / 16th / n/a	16th / 16th / n/a	16th / 16th / n/a	16th / 16th / n/a	16th / 16th / n/a	16th / 16th / n/a	16th / 16th / n/a
Plot Settings	(any)	(any)	(any)	(any)	(any)	(any)	(any)	(any)	(any)	(any)
Motor Settings
Step Mode	n/a / n/a / 16th	n/a / n/a / 16th	n/a / n/a / 16th	n/a / n/a / 16th	n/a / n/a / 16th	n/a / n/a / 16th	n/a / n/a / 16th	n/a / n/a / 16th	n/a / n/a / 16th	n/a / n/a / 16th
Motor Current	n/a / n/a / Normal	n/a / n/a / Normal	n/a / n/a / Normal	n/a / n/a / Normal	n/a / n/a / Normal	n/a / n/a / Normal	n/a / n/a / Normal	n/a / n/a / Normal	n/a / n/a / Normal	n/a / n/a / Normal
Max Jog Rate	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 1,500
Rot Speed	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 1,500	n/a / n/a / 1,500
Settings	1cc ET	5cc	10cc	30cc	60cc	150cc	DSD-50	HSD-10-Ardes	SDS-30XT	SDS-60XT
	SDS, HSD, and RSD Heads (with or without COD) (Various Tube Diameters, Standard Gear Ratios)						DSD-50 (1:1)	Special (with or without COD)