Difference between revisions of "KCD"

From Hyrel3D
Jump to navigation Jump to search
(Created page with "Category:Hardware Category:Warm_Flow {| align="right" | __TOC__ |} The KCD-15 is our 15cc print head for high viscosity emulsions which print at up to 200°C (KRA-15)...")
 
(Redirected page to KR2)
 
Line 1: Line 1:
[[Category:Hardware]]
#REDIRECT [[KR2]]
[[Category:Warm_Flow]]
{| align="right"
| __TOC__
|}
 
The KCD-15 is our 15cc print head for high viscosity emulsions which print at up to 200°C (KRA-15), with a UV LED array to photoinitiate crosslinking of photosensitive material.
 
[[File:KCD-15.png|200px|left|KCD-15]]
 
This includes the following materials:
 
<div style="column-count:3;-moz-column-count:3;-webkit-column-count:3">
*Clays, including Metal Clays
*Pastes
*Emulsions
*Hot Glues, including 3M 3796
*UV Crosslinkable Resins
</div>
 
Additionally, the KCD can be used as an EMO, COD, VOL, VCD, or KRA, with or without heat and/or crosslinking.
 
== Videos ==
 
# Overview of the head:
## [[File:Yt.png]] [https://www.youtube.com/watch?v=QD2FrZ4kg1g Overview of the KRA, and KCD Heads]
# Loading the head:
## [[File:Yt.png]] [https://www.youtube.com/watch?v=YWe3TQGgNW0 Loading the VCD Head] (same as the VCD)
 
== Description ==
 
* The KCD-15 has a 15cc stainless steel reservoir with a threaded collar at each end. The tube has to be loaded into the KRA apparatus before the bottom cap is attached. The LED array has three LEDs at a user-specified wavelength to irradiate the deposited material. Industry standard luer tips or needles are available from a variety of sources. The top has a threaded rod, which is how material is displaced; the bottom holds a nozzle, or a nozzle or luer adapter. Industry standard luer tips or needles are available from a variety of sources.
 
== Loading the Head onto the Printer ==
 
As with all Hyrel heads, the following process should be followed:
 
# Start with a level bed and Repetrel running and connected to the printer.
# Load the gibs on the Head into the gib slots on the Yoke from above and slide the head down into place; the last mm of travel should be done gently, ensuring that the electrical connector seats properly (firmly and completely) into the receiving connector.
# Ensure the LEDs on the print head are flashing - this means the Head is communicating with the Motion Controller.
# Tighten the thumbscrew in the rear, to prevent the head from moving relative to the Yoke.
# If the Head doesn't show up in Repetrel, press and release the RESET button on the front of the printer.
# Once the Head is shown in repetrel, proceed to setting your Z-Zero position.
 
== Loading material into the Head ==
 
Loading:
 
* Care should be taken to avoid air pockets, as this will introduce delay when starting and stopping material flow.
 
Unloading:
 
* Unloading is the same process as loading, only in reverse. Tubes and nozzles should be cleaned thoroughly after use.
 
== Default Parameters ==
 
Default settings for the KCD are shown on the [[Cold_and_Warm_Flow]] page.
 
== Adjustments ==
 
The only adjustments needed should be changes to the PRIME and UNPRIME settings, and will have to be dialed in based on how viscous and compressible your material is, and how narrow a nozzle or luer tip you are using.. In dialing in new settings, I usually double or half the settings for both STEPS and TIME, then make another print and reassess.
 
== Firmware ==
 
Please see the [[Downloads]] page for the current firmware for your heads and your version of Repetrel.
 
== Maintenance ==
 
While cleaning your print media from the tube and nozzle after every print is important, very little other maintenance is required on this head.

Latest revision as of 12:51, 23 June 2020

Redirect to:

Retrieved from "https://hyrel3d.in/wiki/index.php?title=KCD&oldid=4830"