Difference between revisions of "Published Papers"

From Hyrel3D
Jump to navigation Jump to search
Line 73: Line 73:
==== Published in 2021 ====
==== Published in 2021 ====


* [https://pubs.rsc.org/en/content/articlelanding/2021/ta/d0ta11341g/unauth#!divAbstract Direct Ink Writing of Recyclable and '''in situ''' Repairable Photothermal Polyurethane for Sustainable 3D Printing Development] by a team from [http://www.at0086.com/shanghu/College.aspx?c=266 School of Mechatronic Engineering and Automation, Shanghai University] and several departments from [https://www.uwo.ca/ The University of Western Ontario]
* [https://pubs.acs.org/doi/abs/10.1021/acsami.0c18095 Ultrathin and Ultrasensitive Printed Carbon Nanotube-Based Temperature Sensors Capable of Repeated Uses on Surfaces of Widely Varying Curvatures and Wettabilities] by a team from [https://eng.umd.edu/ Department of Mechanical Engineering, University of Maryland, College Park]
* [https://pubs.acs.org/doi/abs/10.1021/acsami.0c18095 Ultrathin and Ultrasensitive Printed Carbon Nanotube-Based Temperature Sensors Capable of Repeated Uses on Surfaces of Widely Varying Curvatures and Wettabilities] by a team from [https://eng.umd.edu/ Department of Mechanical Engineering, University of Maryland, College Park]
* [https://www.sciencedirect.com/science/article/abs/pii/S221486042100083X Moisture Sensitivity and Compressive Performance of 3D-Printed Cellulose-Biopolyester Foam Lattices] by a team from [https://www.waikato.ac.nz/study/subjects/engineering School of Engineering, The University of Waikato], [http://www.cacm.auckland.ac.nz/en/cacm.html Centre for Advanced Composite Materials, The University of Auckland], and [https://www.wgtn.ac.nz/design-innovation School of Design Innovation, Victoria University Wellington]
* [https://www.sciencedirect.com/science/article/abs/pii/S221486042100083X Moisture Sensitivity and Compressive Performance of 3D-Printed Cellulose-Biopolyester Foam Lattices] by a team from [https://www.waikato.ac.nz/study/subjects/engineering School of Engineering, The University of Waikato], [http://www.cacm.auckland.ac.nz/en/cacm.html Centre for Advanced Composite Materials, The University of Auckland], and [https://www.wgtn.ac.nz/design-innovation School of Design Innovation, Victoria University Wellington]

Revision as of 18:11, 8 March 2021

Below is a list of published works citing Hyrel equipment.

228 documents as of 25 February 2021.

Non-Traditional Manufacturing

Including Antennas, Sensors, Inductors, and Circuits; Combined Manufacturing Techniques; and Electro-Spinning or Electro-Melt-Spinning

Published in 2021

Published in 2020

Published in 2019

Published in 2018

Published in 2017

Published in 2016

Published in 2015

Unheated or Chilled Reservoir Printing (DIW)

Also known as DIW, Direct Ink Writing.

Published in 2021

Published in 2020

Published in 2019

Published in 2018

Published in 2017

Published in 2016

Published in 2015

Published in 2014

Heated Reservoir Printing (MEW)

Also known as MEW, or Melt Electro-Writing.

Published in 2020

Published in 2019

Published in 2018

Published in 2017

Filament Printing (FFF/FDM)

Also known as FFF or FDM, Fused Filament Fabrication or Fused Deposition Modeling.

Published in 2021

Published in 2020

Published in 2019

Published in 2018

Published in 2017

Published in 2016