Published Papers

Below is a list of published works citing Hyrel equipment.

Count

486 documents as of 8 December, 2023.

Non-Traditional Manufacturing (NTM)

Including:

• Antennas
• Sensors
• Inductors
• Circuits
• Electro-Spinning
• Electro-Melt-Spinning
• Melt Electro-Writing (MEW)
• 4D Printing
• Shape Memory Polymers
• Nanostructures
• Micro-Encapsulated Phase-Changing Materials (MEPCM)
• Printing with Embedded Fibers
• And combining two or more additive manufacturing methods in a single build.

NTM, 2024

• Additively Manufactured Flexible Piezoelectric Wave-Based Multifunctional SensorMultifunctional Sensor, a Master's Thesis submitted to Embry-Riddle Aeronautical University
• Inkjet Printing of a Gate Insulator: Towards Fully Printable Organic Field Effect Transistor by a team from the School of Engineering Technology, Purdue University
• Extremely Stable, Multidirectional, All-in-One Piezoelectric Bending Sensor with Cycle up to Million Level by a team from several departments of Xi'an Jiaotong University, China
• Hybrid 3D Printing of a Nature-Inspired Flexible Self-Adhesive Biopatch for Multi-Biosignal Sensing by a team from King Abdullah University of Science and Technology (KAUST)'s Smart Advanced Memory devices and Applications (SAMA) Lab, Mechanics of Composites for Energy and Mobility Lab, and Biological and Environmental Science and Engineering Division
• Engineering of Functional Hybrid Nanocomposites for Renewable Energy Applications via Laser Ablation, a doctoral dissertation submitted to The University of Tennessee, Knoxville's Department of Chemical and Biomolecular Engineering
• Multiscale 3d Printing via Active Nozzle Size and Shape Control by a team from the Department of civil and Systems engineering, Johns hopkins University
• Versatile Patterning of Liquid Metal via Multiphase 3D Printing by a team from the School of Manufacturing Systems and Networks (MSN), Ira Fulton Schools of Engineering, Arizona State University
• Advancing Interactive Systems With Liquid Crystal Network-based Adaptive Electronics by a team from Eindhoven University of Technology, The Netherlands
• All-printed Multifunctional Sensors for Structural Health Monitoring of Inflatable Habitats by a team from Boise State University
• In-space Manufacturing of Morphing Electronics by a team from Boise State University
• ARJUNA: An Electrochemical Interface Mapping Probe for Solid-State Batteries by a team from Electrification & Energy Infrastructure Division, Oak Ridge National Laboratory
• Recent Advances in Implantable Sensors and Electronics Using Printable Materials for Advanced Healthcare by a team from Georgia Tech, Chungnam National University, University of Washington Tacoma, and Emory University School of Medicine
• Pediatric Formulations Developed by Extrusion-Based 3D Printing: From Past Discoveries to Future Prospects, results compiled by a team from Centre National de la Recherche Scientifique et Technologique (CRNF) and Delpharm, France
• 3D Printing Carbon-Carbon Composites With Multilayered Architecture for Enhanced Multifunctional Properties by a team from Arizona State University, Centre National de la Recherche Scientifique et Technologique (CRNF), Texas A&M University, and University of Georgia
• Direct Ink Writing of Strained Carbon Nanotube-Based Sensors: Toward 4D Printable Soft Robotics by a team from SAMA Laboratories, Electrical and Computer Engineering, Computer Electrical Mathematical Science and Engineering Division, King Abdullah University of Science and Technology (KAUST) and Electrical Engineering, King Fahd University of Petroleum and Minerals (KFUPM)
• Liquid Crystal Elastomer Soft Robotic Arm for Pick-and-place Operation Controlled by Light by a team from Technische Universiteit Eindhoven
• Development of Multimaterial Additive Manufacturing Systems for Embedded Electronics by a team from the Department of Mechanical Engineering, Pennsylvania State University and the Department of Mechanical Engineering, University of Houston
• Direct Ink Writing of 4D Structural Colors by a team from Laboratory of Stimuli-Responsive Functional Materials and Devices (SFD), Department of Chemical Engineering and Chemistry and Institute for Complex Molecular Systems (ICMS) of the Eindhoven University of Technology (TU/e)
• A Flexible and Electrically Conductive Liquid Metal Adhesive for Hybrid Electronic Integration by a team from Virginia Tech
• Low-Roughness 3D Printed Surfaces by Ironing for the Integration with Printed Electronics by a team from the Department of Electrical Engineering and Computer Science, Lassonde School of Engineering, York University, Toronto

NTM, 2023

• Vitrimer Chemistry for 4D Printing Formulation by a team from Sahand University of Technology, Iran, Nottingham Trent University, UK, and Deakin University, Geelong, Australia
• Laser-Induced Graphene Electrodes for OrganicElectrochemical Transistors (OECTs) by a team from Department of Electrical Engineering and Computer Science, Lassonde School of Engineering, York University, Toronto
• 3D Printing-Enabled Design and Manufacturing Strategies for Batteries: A Review by a team partially from Arizona State University
• Permeable Skin Patch with Miniaturized Octopus-Like Suckers for Biosignal Monitoring by a team from King Abdullah University of Science and Technology (KAUST)
• Evaluation of Low-Loss Polymer Switches for Multinuclear MRI/S*by a team primarily from Texas A&M University (TAMU)
• Energy Harvesting Using High-Strength and Flexible 3D-Printed Cellulose/Hexagonal Boron Nitride Nanosheet Composites by a team from several departments of the Institute of Technology, Kharagpur
• Competing Effects of Radio Frequency Fields on CarbonNanotube/Resin Systems: Alignment versus Heating by a team from several departments of Texas A&M University and from Singapore Institute of Manufacturing Technology (SIMTech) Agency for Science Technology and Research (A*STAR)
• Enhancing Photoelectrochemical Performance of the Printed Nanoporous FeVO4 Photoanode by Dual-Layer CoOx–CoPi Catalysts by a team from Duy Tan University, Vietman, Nanyang Technological University, Singapore, The Hebrew University of Jerusalem, Jerusalem , Israel, and City University of Hong Kong, China
• Sustainable Piezoelectric Energy Harvesting Using 3D Printing with Chicken Bone Extract by a team from several departments of the Indian Institute of Technology, Kharagpur and the Defence Materials and Stores Research and Development Establishment (DMSRDE), Kanpur
• Phase Change Materials Incorporation Into 3d Printed Geopolymer Cement: a Sustainable Approach to Enhance the Comfort and Energy Efficiency of Buildings by a team from the Department of Civil and Mechanical Engineering and Department of Chemistry of the Technical University of Denmark and the Faculty of Engineering Technology, Department of Thermal and Fluid Engineering (TFE), University of Twente, the Netherlands
• Navigating Soft Robots through Wireless Heating by a team from Carnegie Mellon University
• Electrical Properties of Pvdf Films Fabricated by Direct Ink Writing by a team from Central South University, China
• Characteristic Analysis of Heterochiral TCP Muscle as a Extensile Actuator for Soft Robotics Applications by a team from the Department of Manufacturing Engineering, Georgia Southern University
• 3D-Printed Elastomer Ternary Composites for Piezoelectric Energy Generation by a team from several departments of Tuskegee University
• Biomimetic Flexible Electronic Materials from Silk Fibroin-MXene Composites Developed via Mussel-Inspired Chemistry as Wearable Pressure Sensors by a team from the Institute of Inorganic Chemistry, Department of Chemistry, University of Cologne, Department of Health Technology, Technical University of Denmark, and Institute of Inorganic Chemistry, Department of Chemistry, University of Cologne
• Self-Assembly-Driven Bi2S3 Nanobelts Integrated a Silk-Fibroin-Based 3D-Printed Aerogel-Based Scaffold with a Dual-Network Structure for Photothermal Bone Cancer Therapy by a team from the Institute of Inorganic Chemistry, University of Cologne, the Department of Chemistry, Materials and Chemical Engineering, Politecnico di Milano, and the Center for Molecular Medicine Cologne (CMMC)
• 3D Printing of Responsive Chiral Photonic Nanostructures by a team from Cornell University's Department of Food Science and University of South Carolina's Departments of Biomedical and Chemical Engineering
• 3D Printed Dry Electrodes for Electrophysiological Signal Monitoring: A Review by a team from King Abdullah University of Science and Technology (KAUST)
• 3D Printing-Assisted Self-Assembly to Bio-Inspired Bouligand Nanostructures by a team from the Department of Chemical Engineering, University of South Carolina
• Conductive and Elastic Bottlebrush Elastomers for Ultrasoft Electronics by a team from a team from a variety of departments of the University of Toronto
• Processes & Toolchain For Automation Of Hybrid Direct-Write 3D Printing, a PhD thesis submitted to the Department of Electrical and Computer Engineering, University of Texas at El Paso

NTM, 2022

• Direct Ink Writing of 4D Structural Colors by a team from Laboratory of Stimuli-Responsive Functional Materials and Devices (SFD), Department of Chemical Engineering and Chemistry and Institute for Complex Molecular Systems (ICMS) of the Eindhoven University of Technology (TU/e)
• 4D Printing of Extrudable and Degradable Poly(Ethylene Glycol) Microgel Scaffolds for Multidimensional Cell Culture by a team from the Department of Chemical and Biological Engineering and the BioFrontiers Institute of the University of Colorado - Boulder and the Medical Scientist Training Program, School of Medicine, University of Colorado - Anschutz Medical Campus
• Structured 3D Printed Dry ECG Electrodes Using Copper Based Filament by a team from King Abdullah University of Science and Technology, Yachay Tech Universiy, and King Abdulaziz University
• Extrusion-Based 3D Printing of Stretchable Electronic Coating for Condition Monitoring of Suction Cups by a team from the Laboratoire de Génie Electrique et Ferroélectricité, Institut National des Sciences Appliquées, Université de Lyon and the Hybria Institute of Business and Technologies
• Enhancing Stability of High-Nickel Cathodes for Lithium-Ion Batteries through Additive Manufacturing of Cathode StructureBatteries through Additive Manufacturing an Honors Thesis submitted to the Mechanical Engineering Department of the University of Arkansas
• Additively Manufactured Unimorph Dielectric Elastomer Actuators with Ferroelectric Particles for Enhanced Low-Voltage Actuation by a team from the Aerospace Engineering Department of Embry-Riddle Aeronautical Univeristy
• Innovation in Additive Manufacturing Using Polymers: A Survey on the Technological and Material Developments, a review of "the most recent advances from technological and physico-chemical perspectives to improve several remaining issues in polymeric materials’ additive manufacturing", by a team from Universidad San Sebastián, Universidad Tecnológica Metropolitana, Santiago, and Instituto de Ciencia y Tecnología de Polímeros-Consejo Superior de Investigaciones Científicas, Chile

NTM, 2021

• 4D-Actuators by 3D-Printing Combined with Water-based Curing by a team from Institute of Active Polymers, Helmholtz-Zentrum Hereon
• 4D Printing of Engineered Living Materials by a team from several departments at [https://www.tamu.edu/ Texas A&M University
• Design and Development of Soft Earthworm Robot Driven by Fibrous Artificial Muscles a thesis presented to Georgia Southern University
• Comprehensive Review on Design and Manufacturing of Bio-scaffolds for Bone Reconstruction by a team from School of Mechanical Engineering Vellore Institute of Technology, India
• Printed Electronic Devices with Inks of TiS3 Quasi-One-Dimensional van der Waals Material by a team from University of California, Riverside and University of Nebraska, Lincoln
• 3D Printing of Thermo-Sensitive Drugs by a team from the University of South Australia and Addis Ababa University
• Printable Elastomeric Electrodes with Sweat-Enhanced Conductivity for Wearables by a team from the School of Materials Science and Engineering, Nanyang Technological University and the School of Electrical Engineering and Automation, Wuhan University
• Optimal Soft Composites for Under-Actuated Soft Robots by a team from The Singapore University of Technology and Design
• Review of Low-Cost 3D Bioprinters: State of the Market and Observed Future Trends
• 3D Printing of Electrically Responsive PVC Gel Actuatorsby a team from the Mechanical and Aerospace Engineering and Materials Science and Engineering departments of The University of California, San Diego
• 4D Printing with Bio-based Polymers for Adaptive Wearable Devices, submitted in fulfillment of the requirements for the degree of Master of Design Innovation
• Automated Fiber Embedding for Soft Mechatronic Components by a team from the Manufacturing and Design Centre of the Singapore University of Technology and Design
• Silicone/Epoxy Hybrid Resins with Tunable Mechanical and Interfacial Properties for Additive Manufacture of Soft Robots by a team from the Manufacturing and Design Centre and the Engineering Product Development Pillar of the Singapore University of Technology and Design
• 3D-Printed Triboelectric Nanogenerators: State of the Art,Applications, and Challenges by a team from the engineering schools of Deakin University, The University of Melbourne, UCLA, and Georgia Tech
• Enhanced Wettability in Ultrasonic-Assisted Soldering to Glass Substrates, by a team from the Department of Mechanical Engineering, Clemson University

NTM, 2020

• 4D Printing of Shape-memory Polymeric Scaffolds for Adaptive Biomedical Implantation by a team from the Department of Mechanical and Aerospace Engineering, the Department of Surgery, the Food Science Program, Division of Food Systems & Bioengineering, and the Department of Biomedical, Biological & Chemical Engineering of the University of Missouri
• Morphing Circuit: An Integrated Design, Simulation, and Fabrication Workflow for Self-morphing Electronics by a team from Carnegie Mellon University and Zhejiang University, China
• An Integrated Manifold Learning Approach for High Dimensional Data Feature Extractions and its Applications to Online Process Monitoring of Additive Manufacturing by a team from Oak Ridge National Laboratory, Virginia Tech, and Oklahoma Stata University, funded by the National Science Foundation and the Office of Naval Research
• Additive Manufacturing Techniques for Smart Prosthetic Liners by a team from several departments of the University College London in cooperation with the Royal National Orthopaedic Hospital, Stanmore, UK
• Guideline for Paste Extrusion 3D Printing of Slump-Free Ferrite Inductor Cores by a team from Virginia Tech's Materials Science and Engineering Department, Center for Power Electronics Systems, and Bradley Department of Electrical and Computer Engineering
• Reliability Assessment of Magnetic Cores and 3D-printed Constant-flux Inductors by a team from Virginia Tech and Texas Instruments
• Z-Meandering Miniaturized Patch Antenna Using Additive Manufacturing by a team from Aerospace Engineering at Embry-Riddle Aeronautical University
• Wetting Analysis of the Ultrasonic-Assisted Soldering Process, a thesis submitted to The Mechanical Engineering Department of Clemson University
• Solid Dosage Form Production, a patent application by a team from the School of Pharmacy and Biomedical Sciences of the University of Central Lancashire
• Flexible Fiber Interconnects For Soft Mechatronics by a team from the Singapore University of Technology and Design (SUTD)

NTM, 2019

• UHF RFID-based Additively Manufactured Passive Wireless Sensor for Detecting Micrometeoroid and Orbital Debris Impacts by a team from Aerospace Engineering at Embry-Riddle Aeronautical University
• Bi-Layered Polymer Carriers with Surface Modification by Electrospinning for Potential Wound Care Applications by the Institute of Pharmacy, University of Tartu, Estonia and the Pharmeceutical Sciences laboratory at Abo Akademi University, Finland
• Additive Manufacturing of Spiral Windings for a Pot-core Constant-flux Inductor by a team from the Material Science & Engineering Department of Virginia Tech
• Additive Manufacturing Technologies for Aerospace Applications by NASA
• Isolation, Characterization, and Agent-Based Modeling of Mesenchymal Stem Cells in a Bio-construct for Myocardial Regeneration Scaffold Design by a team from the Universidad Autónoma de Occidente de Cali - Colombia and the University of Applied Sciences and Arts, Western Switzerland

NTM, 2018

• 3D‐Printed Gastric Resident Electronics by a team from The Koch Institute for Integrative Cancer Research at MIT
• 3D Printed Capsules for Quantitative Regional Absorption Studies in the GI Tract by a team from Merck Pharmaceuticals
• Fused Deposition Modelling: Advances in Engineering and Medicine in 3D Printing of Pharmaceuticals
• Block Copolymer Ink Formulation for 3D Printing and Method of Making a 3D Printed Radiofrequency (RF) Device by a team from the the Massachusetts Institute of Technology (MIT) and Harvard University
• Hybrid Processes in Additive Manufacturing by a team primarily from the University of Nebraska–Lincoln's Department of Mechanical & Materials Engineering
• Additive Manufacturing- A Review of 4D Printing and Future Applications by a team from The European Space Research and Technology Center
• Molecularly-Engineered, 4D-Printed Liquid Crystal Elastomer Actuators by a team from the Bioengineering Department of University of Texas, Dallas

NTM, 2017

• Additive Manufacturing of Toroid Inductor for Electronics Applications by Chao Ding, Virginia Tech
• Self-Actuating 3D Printed Packaging for Deployable Antennas, by a team from Georgia Tech
• A Preliminary Study of Conductive Filaments Printed Via Fused Filament Fabrication by Smruti Ranjan Sahoo at Rochester Institute of Technology
• Review of Batteryless Wireless Sensors Using Additively Manufactured Microwave Resonators in Sensors, a Journal of the Multidisciplinary Digital Publishing Institute
• 4D Printing of Liquid Crystal Elastomers by a team from the Bioengineering Department of the University of Texas, Dallas

NTM, 2016

• Additive Manufacturing of Planar Inductor for Power Electronics Applications by a team from Virginia Tech
• A Low-Cost, Single Platform, Hybrid Manufacturing System for RF Passives, The Institute of Electrical and Electronics Engineers, Incorporated (IEEE)
• Nano-Material Based Flexible Radio Frequency Sensors for Wearable Health and Environment Monitoring: Designs and Prototypes Utilizing 3D/Inkjet Printing Technologies, A Dissertation Presented to The Academic Faculty of The School of Electrical and Computer Engineering at Georgia Tech
• A Novel Approach to Integrating 3D/4D Printing and Stretchable Conductive Adhesive Technologies for High Frequency Packaging Applications by a team from Georgia Tech

NTM, 2015

• Infill Dependent 3D-Printed Material Based on NinjaFlex Filament for Antenna Applications, The Institute of Electrical and Electronics Engineers, Incorporated (IEEE)
• A Novel Strain Sensor Based on 3D Printing Technology and 3D Antenna Design, The Institute of Electrical and Electronics Engineers, Incorporated (IEEE)
• A Novel 3-D Printed Loop Antenna Using Flexible NinjaFlex Material for Wearable and IoT Applications, The Institute of Electrical and Electronics Engineers, Incorporated (IEEE)
• Button-Shaped RFID Tag Combining Three-Dimensional and Inkjet Printing Technologies, The IET Digital Library.
• Demonstration and Characterization of Fully 3D-printed RF Structures, The Institute of Electrical and Electronics Engineers, Incorporated (IEEE)
• RF Characterization of 3D Printed Flexible Materials - NinjaFlex Filaments, The European Microwave Association (EuMA)

Unheated or Chilled Reservoir Printing (DIW, SEP, SSE, 3DCP, DCC)

Also known as Robocasting or DIW (Direct Ink Writing), SEP (Semisolid Extrusion Printing), SSE (Semisolid Extrusion). 3DCP' (3D Concrete Printing), or DCC (Digital Concrete Construction).

DIW/SEP/SSE, 2023

• Processing of Bioceramics by Additive Manufacturing, affiliation unknown
• Semisolid Extrusion Printing and 3D Bioprinting by a team from College of Pharmacy, The University of Texas at Austin and School of Pharmacy, University of Mississippi
• Size-dependent Viscoelasticity in Hybrid Colloidal Gels Based on Spherical Soft Nanoparticles and Two-dimensional Nanosilicates of Varying Size by a team from the University of South Carolina
• DC Resistance Measurements in Multi-Layer Additively Manufactured Yttrium Barium Copper Oxide Components by a team from Loughborough University, UK
• Morphology Map-guided Identification of Bijel Ink for Producing Conductive Porous Structures by a team from Texas A&M University
• Peritoneal Implants and Drug Delivery by a team from several departments of Government College University, Faisalabad, Pakistan, Government College University, Lahore, Pakistan, and University of Lahore, Lahore, Pakistan
• A Bioinspired and Sustainable Route for the Preparation of Ag-crosslinked Alginate Fibers Decorated With Silver Nanoparticles by a team from the University of Florence and the Université de Strasbourg, France
• Radio Frequency-assisted Curing of on-chip Printed Cnt/silicone Heatsinks Produced by Material Extrusion 3d Printing by a team from Singapore Institute of Manufacturing Technology (SIMTech), Agency for Science, Technology and Research (A⁎STAR) and from Texas A&M University's departments of Chemical Engineering and Materials Science & Engineering
• Multimaterial Hydrogel 3D Printing by a team from School of Chemical Sciences The University of Auckland
• Fabrication of Gentamicin Sulfate-Loaded 3D-PrintedPolyvinyl Alcohol/Sodium Alginate/Gelatin-MethacryloylHybrid Scaffolds for Skin Tissue Replacement by a team from several departments of Marmara University, Istanbul
• Sintering Energy Conservation in Extrusion-based 3d Printing of Porcelain Ceramics Blended With Copper and Allied Alloys: a Sustainable Approach by a team from the Department of Mechanical Engineering, Indian Institute of Technology Tirupati
• Ultrasensitive and Robust Mechanoluminescent Living Composites by a team from multiple departments of the University of California, San Diego and from the Van der Waals-Zeeman Institute, Institute of Physics, University of Amsterdam
• Applicability of UV-Curable Binders in High Solid Suspensions for Direct-Ink-Write 3D Printing in Extremely Cold Temperatures by a team from the NASA Marshall Space Flight Center and Georgia Tech's School of Chemical and Biomolecular Engineering and School of Mechanical Engineering
• 3d Printing to Enable Photocatalytic Process Engineering: a Critical Assessment and Perspective by a team from Materials Research and Technology (MRT) Department, Luxembourg Institute of Science and Technology (LIST) and several departments at King Abdullah University of Science and Technology
• Recent Progress on the 3D Printing of Dynamically Cross-Linked Polymers by a team from the School of Materials Science and Engineering, Henan University of Technology
• 3d Printing of Tough Nature Inspired Hierarchical Architecture Using Chicken Bone and Eggshell Biowaste for Biomedical Applications by a team from several locations of the Indian Institutes of Technology and from Morgan Advanced Materials, State College, PA
• 3d-printing Formulated Polyelectrolyte Complexes (Pecs) in Air: Silica Compositions in Rheological Optimization for Layering by a team from The University of Tennessee, Knoxville, TN and North Dakota State University, Fargo, ND
• Semi-solid Extrusion 3d-printing of Eucalypt Extract-loaded Polyethylene Oxide Gels Intended for Pharmaceutical Applications by a team from Institute of Pharmacy, Faculty of Medicine, University of Tartu, Estonia, National University of Pharmacy, Kharkiv, Ukraine, Ivano-Frankivsk National Medical University, Ivano-Frankivsk, Ukraine, and CurifyLabs, Helsinki, Finland
• Fabrication and Characterization of Advanced Epoxy-based Composites and Nanocomposites, a PhD thesis submitted to Rice University
• Future Directions in Ceramic Additive Manufacturing: Fiber Reinforcements and Artificial Intelligence by a team from the US Air Force Research Laboratory
• Polymer/Coal Composites from Ink-based Additive Manufacturing, a Masters thesis submitted to Arizona State University
• A Conformal Heat-drying Direct Ink Writing 3d Printing for High-performance Lithium-ion Batteries by a team from Electrification and Energy Infrastructures Division, Oak Ridge National Laboratory, Center for Nanophase Materials Sciences, Oak Ridge National Laboratory, and Department of Mechanical and Aerospace Engineering, Case Western Reserve University
• Semi-solid Extrusion 3d-printing of Eucalypt Extract-loaded Polyethylene Oxide Gels Intended for Pharmaceutical Applications by a team from Institute of Pharmacy, Faculty of Medicine, University of Tartu, The National University of Pharmacy, Kharkiv, Ukraine, CurifyLabs, and Ivano-Frankivsk National Medical University, Ivano-Frankivsk, Ukraine
• Deep-learning-assisted Printed Liquid Metal Sensory System for Wearable Applications and Boxing Training by a team from College of Mechanical Engineering, Zhejiang University of Technology, Department of Mechanical Engineering, University of Colorado Boulder, and College of Information Engineering, Zhejiang University of Technology
• Development of Bean-based Emulgels for 3d Printing Applications: Feasibility for Dysphagia Diets by a team from the Universidad del Bío-Bío, Chile and Universidad de Santiago de Chile
• On the 3d Printing of Polyelectrolyte Complexes: a Novel Approach to Overcome Rheology Constraints by a team from Department of Coatings and Polymeric Materials, North Dakota State University, Fargo, Department of Macromolecular Sciences and Engineering, Case Western Reserve University, Center for Nanophase Materials and Sciences, Oak Ridge National Laboratory, and multiple departments of University of Tennessee, Knoxville
• Carbon Scaffold Architectures for Stable Lithium Metal Anodes, a paper from Lawrence Livermore National Laboratory
• Printing Composites with Salt Hydrate Phase Change Materials for Thermal Energy Storage by a team from the Chemistry, Mechanical Engineering, and Materials Science & Engineering departments of Texas A&M University
• Drug Delivery and Testing via 3D Printing by a team from the College of Pharmacy, Pandit Bhagwat Dayal Sharma University of Health Sciences, Rohtak and Department of Pharmaceutical Sciences, Maharshi Dayanand University, Rohtak
• On the 3d Printability of One-part Moisture-curable Polyurethanes via Direct Ink Writing (DIW) by a team from the University of Tennessee, Knoxville, Case Western Reserve University, Novagard Solutions, and the Center for Nanophase Materials and Sciences, Oak Ridge National Laboratory
• Enhancing Photoelectrochemical Performance of the Printed Nanoporous FeVO4 Photoanode by Dual-Layer CoOx–CoPi Catalysts by a team from Duy Tan University, Vietman, Nanyang Technological University, Singapore, The Hebrew University of Jerusalem, Jerusalem , Israel, and City University of Hong Kong, China
• D Printed Styrax Liquidus (Liquidambar Orientalis Miller)-loaded Poly (L-lactic Acid)/chitosan Based Wound Dressing Material: Fabrication, Characterization, and Biocompatibility Results by a team from Kartal Prof. Dr. Saban Teoman Durali Science and Art Center, Istanbul, Marmara University, Istanbul University-Cerrahpasa, Halic University, Koç University, Goztepe Prof. Dr. Suleyman Yalcin City Hospital, and Istanbul Arel University, all in Turkey
• 3D Printing, Histological, and Radiological Analysis of Nanosilicate-Polysaccharide Composite Hydrogel as a Tissue-Equivalent Material for Complex Biological Bone Phantom by a team from multiple departments of the Medical University of Varna, Bulgaria
• PDMS-silica Composite Gas Separation Membranes by Direct Ink Writing by a team from University of the Philippines Diliman, University of Tennessee, Knoxville, Case Western Reserve University, North Dakota State University, and Oak Ridge National Laboratory
• Ceramic Materials for 3d Printing of Biomimetic Bone Scaffolds – Current State-of-the-art & Future Perspectives by a team from TCentre for Nanotechnology & Advanced Biomaterials, School of Chemical & Biotechnology, SASTRA Deemed University, India and Orthopaedics and Musculoskeletal Sciences, Univeristy College, London
• Pharmaceutical 3D-Printing of Nanoemulsified Eucalypt Extracts and Their Antimicrobial Activity by a team from Institute of Pharmacy, Faculty of Medicine, University of Tartu, The National University of Pharmacy, Ukraine, and Curify Labs, Finland
• Texture in Silicon Carbide via Aqueous Suspension Material Extrusion and Seeded Grain Growth by a team from Purdue University
• Shape Memory Soft Robotics with Yield Stress Fluids by a team from the University of Amsterdam and the Eindhoven University of Technology (TU Eindhoven)
• Multimaterial Printing of Liquid Crystal Elastomers with Integrated Stretchable Electronics by a team from the Department of Mechanical Engineering and the Human Computer Interaction Institute of Carnegie Mellon University, and from the Institute of Systems and Robotics, Department of Electrical Engineering, University of Coimbra
• Robocasting of Ceramic Fischer–Koch S Scaffolds for Bone Tissue Engineering by a team from the Department of Mechanical Engineering, the Department of Computer Science, the School of Biomedical Engineering and the Department of Mathematics of Colorado State University
• In Vitro Electrically Controlled Amoxicillin Release from 3D-Printed Chitosan/Bismuth Ferrite Scaffolds by a team from the Department of Bioengineering, Faculty of Chemistry and Metallurgy, Yildiz Technical University, the BioMatter unit - École polytechnique de Bruxelles, Université Libre de Bruxelles, the College of Life Sciences, Xinyang Normal University (XYNU), and the Center for Nanotechnology and Biomaterials Application & Research (NBUAM), Department of Metallurgical and Materials Engineering, and Faculty of Pharmacy of Marmara University
• Evaluation of Physicochemical Properties of Starch-Protein Gels: Printability and Ppostprocessing by a team from Universidad del Bío-Bío and Universidad de Chile
• EpoMemory: Multi-state Shape Memory for Programmable Morphing Interfaces by a team from different departments of Carnegie Mellon University
• Additive Manufacturing of Highly Flexible Impact Wave Propagation Sensor by a team from Los Alamos National Laboratory and The University of Texas at El Paso
• 3D Bioprintable Hypoxia-Mimicking PEG-Based Nano Bioink for Cartilage Tissue Engineering by a team from the Indian Institute of Technology (IIT) Hyderabad,'s Regenerative Medicine and Stem cell (RMS) Lab, Department of Biomedical Engineering and Department of Materials Science and Metallurgical Engineering, as well as the Sri Manjeera Super Specialty Hospital, Department of Obstetrics and Gynecology, Sangareddy
• Electrically Controlled Liquid Crystal Elastomer Surfaces forDynamic Wrinkling by a team from Carnegie Mellon University's Department of Mechanical Engineering and Human-Computer Interaction Institute and the Mechanical and Industrial Engineering Department, University of Massachusetts
• A Literature Review of Additive Manufacturing in the Fabrication of Soft Robots: Main Techniques, Applications, and Related Industrial-Sized Machines by a team from SENAI CIMATEC University Center, Brazil
• Development and Optimization of 3D-Printed Flexible Electronic Coatings: A New Generation of Smart Heating Fabrics for Automobile Applications by a team from the Electrical Department, Ladoua Campus, University Lyon, INSA-Lyon and TESCA-Group
• 2D Stationary Computational Printing of Cement-based Pastes with Time-Dependent Rheology by a team from the Department of Chemical Engineering, Tennessee Technical University
• 3D Printing of a Biocompatible Nanoink Derived from Waste Animal Bones by a team from various departments of the Kharagpur, Gandhinagar, and Varanasi (BHU) campuses of the Indian Institutes of Technology
• Assessing the Robustness of Cement-Hydrogel-Based Binders as 3D Printing Materials by a team from Department of Chemical Engineering, Tennessee Tech University
• 3D Printable Hydrogel with Tunable Degradability and Mechanical Properties as a Tissue Scaffold for Pelvic Organ Prolapse Treatment by a team from Arizona State University's The Polytechnic School (TPS), Ira A. Fulton Schools of Engineering, Department of Biomedical Engineering, School of Biological and Health Systems Engineering (SBHSE), andThe School of Manufacturing Systems and Networks (MSN), Ira A. Fulton Schools of Engineering; from The Mayo Clinic's Arizona departments of Department of Immunology, Head and Neck Regenerative Medicine Laboratory, Department of Medical and Surgical Gynecology, and Division of Laryngology, Department of Otolaryngology; and the Faculty of Engineering, Institute of Nanotechnology, Gonda Brain Research Center, Bar-Ilan University
• Acrylic Sealants as Practicable Direct Ink Writing (DIW) 3D-Printable Materials by a team from the following organizations: Department of Macromolecular Sciences and Engineering, Case Western Reserve University, Novagard Solutions, Advanced Functional Materials & Nanotechnology Group, Centro de Investigación en Materials Avanzados S. C. (CIMAV-Unidad Monterrey), Department of Chemical and Biomolecular Engineering, Institute for Advanced Materials and Manufacturing, University of Tennessee, Knoxville, Department of Materials Science and Engineering and Institute for Advanced Materials and Manufacturing, University of Tennessee, Knoxville, Department of Coatings and Polymeric Materials, North Dakota State University, and Center for Nanophase Materials and Sciences, Oak Ridge National Laboratory
• Influence of Binder Concentration in Zeolitic ZSM-5/bentonite 3D-printed Monoliths Manufactured through Robocasting for Catalytic Applications by a team from the International Hellenic University and the Centre for Research and Technology Hellas (CERTH)
• A Novel Approach for the Fabrication of 3D-Printed Dental Membrane Scaffolds including Antimicrobial Pomegranate Extract by a team primarily from Marmara University
• 3D Printing of Doped Barium-titanate Using Robocasting - Toward New Generation Lead-free Piezoceramic Transducers by a team from the INSA-Lyon and Thales Research & Technology
• Comparison of Machine Learning Algorithms for Natural Gas Identification with Mixed Potential Electrochemical Sensor Arrays by a team from the Department of Physics, Yale University and the Center for MicroEngineered Materials, University of New Mexico
• Effect of Particle Size on Additive Manufacturing of Complex Architecture of Silicon Carbide by a team from the Indian Institute of Technology's Kharagpur, (BHU) Varanasi, and Gandhinagar campuses, and well as the Vikram Sarabhai Space Centre
• Direct Ink Write And Thermomechanical Characterization Of Thermoset Composites, a Master's thesis submitted to the Department of Mechanical Engineering, University of Texas at El Paso
• Material Extrusion of Highly-Loaded Silicon Nitride Aqueous Inks for Solid Infilled Structures by a team from Materials and Manufacturing Directorate, Air Force Research Laboratory, National Research Council Research Associate Program, UES, Inc., Strategic Ohio Council for Higher Education, and General Electric Research
• Printed Carbon Nanotube-Based Humidity Sensors Deployable on Surfaces of Widely Varying Curvatures by a team from the Department of Mechanical Engineering of the University of Maryland
• Nanomechanical Characterization of 3D Printed Cement Pastes by a team from Vanderbilt University's [https://engineering.vanderbilt.edu/chbe/ Department of Chemical and Biomolecular Engineering and Department of Civil and Environment Engineering
• Triplet Fusion Upconversion for Photocuring 3D Printed Particle-Reinforced Composite Networks by a team from the Department of Chemistry, University of Washington and the Department of Chemistry, Columbia University

DIW/SEP/SSE, 2022

• Halloysite Reinforced 3D-printable Geopolymers by a team from The Technical University of Denmark's Departments of Civil & Mechanical Engineering, Physics, Heath Technology, and Nanolab, as well as the Department of Civil and Environmental Engineering, Imperial College London
• Direct Ink Write 3D printing of Wave Propagation Sensor by a team from Los Alamos National Laboratory and from [http://utep.edu The University of Texas at El Paso
• 3D-printable Cyclic Peptide Loaded Microporous Polymers for Antimicrobial Wound Dressing Materials by a team from the Chemistry Division, U.S. Naval Research Laboratory
• MultimodalIimaging Compatible Micro-Physiological System by a team from Department of Radiology, Texas Children's Hospital and Baylor College of Medicine's Departments of Radiology and Pediatrics-Oncology
• Electric poling-assisted additive manufacturing technique for piezoelectric active poly(vinylidene fluoride) films: Towards fully three-dimensional printed functional materials by a team from Purdue University's School of Engineering Technology, School of Materials Engineering, and School of Industrial Engineering,
• Extrusion-Based 3D Printing of Stretchable Electronic Coating for Condition Monitoring of Suction Cups by a team from Laboratoire de Génie Electrique, INSA Lyon and Hybria Institute of Business and Technologies, Écully Campus
• Fabrication of 3D Printed Complex cConcentrated Alloys using Oxide Precursors by a team from Georgia Tech's School of Materials Science and Engineering and Department of Biomedical Engineering
• 3D-Printed PDMS-based Membranes for CO₂ Separation Applications by a team from Oak Ridge National Labratory's Center for Nanophase Materials and Sciences and Chemical Sciences Division, the Department of Macromolecular Sciences and Engineering, Case Western Reserve University, the Institute for Advanced Materials and Manufacturing, University of Tennessee Research Park, the Department of Mining, Metallurgical, and Materials Engineering, University of the Philippines, the Department of Coatings and Polymeric Materials, North Dakota State University, and University of Tennessee, Knoxville's Department of Chemical and Biomolecular Engineering and Department of Chemistry
• Performance of Lithium-Ion Batteries with 3D Printed Anodes and Compressible Carbon Structures, by Lawrence Livermore National Laboratory
• Controlled Release of Metformin-Loaded SA/PEG Scaffolds produced by 3D-Printing Technology], published by Yildiz Technical University Press
• Thermal and UV Curable Formulations of Poly(propylene glycol)–Poly(hydroxyurethane) Elastomers toward Nozzle-Based 3D Photoprinting by a team from the University of Liège
• Mechanical Characterization of 3D-Printed Silicone/Epoxy Hybrids by a team from the Digital Manufacturing and Design Centre and the Engineering and Product Development Pillar of the Singapore University of Technology and Design
• Freeform Liquid 3D Printing of Hydraulically Enhanced Dielectric Actuators by a team from Singapore University of Technology and Design
• Viscoelastic and Thixotropic Characterization of Paraffin/Photopolymer Composites for Extrusion-Based Printing by a team from the departments of Chemestry, Mechanical Engineering, and Materials Science and Engineering, Texas A&M University
• Additive Manufacturing of Nanotube-loaded Thermosets via Direct Ink Writing and Radio-Frequency heating and Curing by a team from The Artie McFerrin Department of Chemical Engineering, Texas A&M University, the Department of Materials Science and Engineering, Texas A&M University, the Chemical Engineering Department, Bolu Abant Izzet Baysal University, and the Singapore Institute of Manufacturing Technology (SIMTech)
• 3D-Printed PCL Scaffolds Combined with Juglone for Skin Tissue Engineering by a team from Marama University's Center for Nanotechnology & Biomaterials Application and Research (NBUAM), Department of Metallurgical and Materials Engineering, Institute of Pure and Applied Sciences, Department of Biochemistry, Faculty of Medicine, Department of Medical Microbiology, Faculty of Medicine, and from University Politehnica of Bucharest's Department of Science and Engineering of Oxide Materials and Nanomaterials, Faculty of Applied Chemistry and Materials Science, National Centre for Micro- and Nanomaterials, National Centre for Food Safety, and Department of Inorganic Chemistry, Physical Chemistry and Electrochemistry, Faculty of Applied Chemistry and Materials Science
• Direct-Write Additively Printed Electronics for 3-Dimensional Electromagnetic Structures and Radio-Frequency Circuit Elements, a PhD dissertation submitted to the Materials Science and Engineering Department of Binghamton University, State University of New York
• Material Extrusion Additive Manufacturing of Dense Pastes Consisting of Macroscopic Particles by a team from the Georgia Tech School of Chemical & Biomolecular Engineering
• Photodegradation of Air and Water Contaminants Using 3D-Printed TiO2 Nanoparticle Scaffolds by a team from CIMAV - Subsede Monterrey and Chihuahua and Universidad Autónoma de Nuevo León
• Enhancing Interfacial Layer Adhesion Strength in 3D Printable Soft Materials by a team from Georgia Southern University
• A Comparative Study of Silver Microflakes in Digitally Printable Liquid Metal Embedded Elastomer Inks for Stretchable Electronics by a team from the Department of Mechanical Engineering, Carnegie Mellon University and the Department of Electrical Engineering, University of Coimbra
• Hybrid Colloidal Gels with Tunable Elasticity Formed by Charge-Driven Assembly between Spherical Soft Nanoparticles and Discotic Nanosilicates by a team from the Department of Chemical Engineering and the Biomedical Engineering Program of the University of South Carolina
• Effect of Additive Manufacturing onß-PhasePoly(Vinylidene Fluoride)-Based Capacitive TemperatureSensors by a team from the School of Engineering Technology, Purdue University
• Silk Fibroin as a Bioink – A Thematic Review of Functionalization Strategies for Bioprinting Applications by a team from the National University of Singapore
• Evaluation of Durability of 3D-Printed Cementitious Materials for Potential Applications in Structures Exposed to Marine Environments by a team primarily from the Lyles School of Civil Engineering, Purdue University
• 3D Printed Interdigitated Supercapacitor using Reduced Graphene Oxide-MnOx/Mn3O4 Based Electrodes by a team from the University of Tennessee, Knoxville
• 3D Printable Ceramic Pastes Design: Correlating Rheology & Printability by a team from Nano & Micro Additive Manufacturing of Polymers and Composite Materials Laboratory ‘‘3D LAB’’, Advanced Functional Materials & Nanotechnology Group, Centro de Investigación en Materiales Avanzados S.C. (CIMAV-Subsede Monterrey) and Materials Chemistry Department, Centro de Investigación en Materiales Avanzados S.C. (CIMAV-Chihuahua) in Mexico
• 2D Stationary Computational Printing of Cement-based Pastes by a team from the Department of Chemical Engineering, Tennessee Technological University
• Investigation of 3D-printed Chitosan-Xanthan Gum Patches by a team from ten universities from Turkey, Poland, India, and the UK.
• Additive Manufacturing of Carbon Steels Through Direct Ink Write Printing of Oxide Precursors, a thesis presented to Georgia Tech School of Materials Science and Engineering
• Computer-Aided Tuning of Silica/poly(dimethylsiloxane) Composites for 3D Printing Process: A Computational and Experimental Study by a team from the Chemical Diagnostics and Engineering Group at Los Alamos National Laboratory, the Future Convergence Technology Research Institute, Gyeongsang National University, and the Korean Institute of Science and Technology
• Scalable Mmanufacturing of Sustainable Packaging Materials with Tunable Thermoregulability by a team from the Departments of Chemical and Biomolecular Engineering, Materials Science and Engineering, and Chemistry of the University of California, Irvine
• Charge-Density-Wave Thin-Film Devices Printed with Chemically Exfoliated 1T-TaS₂ Ink by a team from the Department of Chemistry, University of Georgia and the Departments of Electrical and Computer Engineering and Chemical and Environmental Engineering of the University of California, Riverside
• Print Fidelity Metrics for Additive Manufacturing of Cement-based Materials, by a team from the US National Institute of Science and Technology (NIST) and the Departments of Chemical Engineering and Electrical and Computer Engineering of Tennessee Technological University
• Compressive Properties and Failure Behavior of Photocast Hydroxyapatite Gyroid Scaffolds Vary with Porosity, by a team from the Schools of Advanced Materials Discovery and Biomedical Engineering from Colorado State University
• UV-Assisted Direct Ink Writing of Si3N4/SiC Preceramic Polymer Suspensions by a team from the Materials and Manufacturing Directorate, US Air Force Research Laboratory
• Application of Additively Manufactured 3D Scaffolds for Bone Cancer Treatment: a Review by a team from Department of Mechanical, Aerospace and Civil Engineering, School of Engineering, Faculty of Science and Engineering, The University of Manchester
• The Use of Natural Products in 3D Printing of Pharmaceutical Dosage Forms by Centre for Natural Products Discovery, School of Pharmacy and Biomolecular Sciences, Liverpool John Moores University
• Supplementary Information: Printable, Castable, Nanocrystalline Cellulose-Epoxy Composites Exhibiting Hierarchical, Nacre-like Toughening by a team from the Department of Mechanical Engineering and Department of Civil and Environmental Engineering of the Massachusetts Institute of Technology (MIT)
• Recent Progress in Three-Dimensionally-Printed Dosage Forms from a Pharmacist Pperspective by a team from the School of Pharmacy, Faculty of Medicine and Health, University of Sydney, Procter & Gamble, and Department of Mathematical Sciences, Florida Institute of Technology
• Wood Warping Composite by 3D Printing by a team from the Hebrew University of Jerusalem
• Additive-Free, Gelled Nanoinks as a 3D Printing Toolbox for Hierarchically Structured Bulk Aerogels by a team from Institute for Nanostructure and Solid State Physics, Center for Hybrid Nanostructures (CHyN), The Hamburg Centre for Ultrafast Imaging, Center for X-ray and Nano Science CXNS, Deutsches Elektronen-Synchrotron DESY, Helmholtz Imaging Platform, Deutsches Elektronen-Synchrotron DESY, and Institute of Inorganic and Applied Chemistry, University of Hamburg
• High-Temperature Interactions of Metal Oxides and a PVDF Binder by a team from University of Maryland, College Park
• 3D Printing of Ecologically Active Soil Structures by a team from the University of Virginia
• In Vitro and In Vivo Evaluation of 3D Printed Sodium Alginate/Polyethylene Glycol Scaffolds for Sublingual Delivery of Insulin: Preparation, Characterization, and Pharmacokinetics by a team from Marmara University
• Anisotropic Mechanical Behavior of 3D Printed Liquid Crystal Elastomer by a team from University of California, San Diego
• Blue Ceramics: Co-designing Morphing Ceramics for Seagrass Meadow Restoration by a team from Carnegie Mellon University, the Hebrew University of Jerusalem, and Bezalel Academy of Art and Design
• Microwave Stimulation of Energetic Al-Based Nanoparticle Composites for Ignition Modulation by a tem from the University of California, Riverside, Georgia Tech, and the University of Maryland
• Processing of Preceramic Polymers for Direct-Ink Writing, a PhD dissertation submitted to University of Tennessee, Knoxville
• Charge-Density-Wave Devices Printed with the Ink of Chemically Exfoliated 1T-TaS2 Fillers, by a team from the Nano-Device Laboratory and Phonon Optimized Engineered Materials Center, Department of Electrical and Computer Engineering, University of California, Riverside, the Department of Chemical and Environmental Engineering, University of California, Riverside, and the Department of Chemistry, University of Georgia
• Functionalization of Thermoresponsive Hydrogels for Topical Delivery of Cellular and Pharmaceutical Payloads to the Intestine, a PhD dissertation submitted to Northeastern University's Department of Chemical Engineering

DIW/SEP/SSE, 2021

• Rheological Characterization of 3D Printable Geopolymers by a team from several departments of the Technical University of Denmark, Civil and Environmental Engineering, Imperial College London, and Dentistry - Regenerative Biomaterials, Radboud Institute for Molecular Life Sciences, Radboud University Medical Center, the Netherlands
• Anisotropic Iridescence and Polarization Patterns in a Direct Ink Written Chiral Photonic Polymer by a team from Laboratory of Stimuli-Responsive Functional Materials and Devices (SFD), Department of Chemical Engineering and Chemistry, Eindhoven University of Technology (TU/e) and T&I, SABIC, both in The Netherlands.
• Direct Ink Write Multi-Material Printing of PDMS-BTO Composites with MWCNT Electrodes for Flexible Force Sensors by a team from the University of Texas at El Paso and the U.S. Department of Energy's Kansas City National Security Campus
• Printed Copper-Nanoplate Conductor for Electro-Magnetic Interference by a team from several departments of the State University of New York at Buffalo
• Patterned Actuators via Direct Ink Writing of Liquid Crystals by a team from the Laboratory for Stimuli-responsive Functional Materials & Devices of the Department of Chemical Engineering and Chemistry of Eindhoven University of Technology and the Center for Responsive Soft Matter, Department of Mechanical Engineering, Indian Institute of Technology Madras, Chennai
• Valorization of Salmon Industry By-Products: Evaluation of Salmon Skin Gelatin as a Biomaterial suitable for 3D Food Printing by a team from Food Engineering Department, Universidad del Bío-Bío and Department of Food Science and Chemical Technology, Faculty of Chemical Sciences and Pharmacy, Universidad de Chile
• 3D Printing of Transparent Silicone Elastomers by a team from Lawrence Livermore National Laboratory
• Effects of Transglutaminase Cross-Linking Process on Printability of Gelatin Microgel-Gelatin Solution Composite Bioink by a team from the University of Florida
• 3D Printing of Osage Orange Extract/Chitosan Scaffolds for Soft Tissue Engineering by a team from Marmara University and Yildiz Technical University
• Factors Affecting Substrate Heating with Printed Thermites from Dr. Matthew Ervin, US Army Research Laboratory
• Effects of Crosslinking on the Physical Solid-State and Dissolution Properties of 3D-printed Theophylline Tablets by a team from the University of Tartu and the University of Helsinki
• Long-term Stabilized Amorphous Calcium Carbonate—an Ink for Bio-inspired 3D Printing by a team from the Bio-Inspired Surface Engineering and Biomineralization Lab of Technion University
• Direct Ink Write 3D Printing of High Solids Loading Bimodal Distributions of Particles by a team from Georgia Tech's schools of School of Material Science and Engineering and School of Chemical and Biomolecular Engineering
• Additively Manufactured Dielectric Elastomer Actuators: Development and Performance Enhancement Development and Performance, a thesis submitted for a PhD in Aerospace Engineering at Embry-Riddle Aeronautical University
• 3D Printing of Antibacterial, Biocompatible, and Biomimetic Hybrid Aerogel-Based Scaffolds with Hierarchical Porosities via Integrating Antibacterial Peptide-Modified Silk Fibroin with Silica Nanostructure by a team primarily from Department of Chemistry, Institute of Inorganic Chemistry, University of Cologne
• Printable, cCastable, Nanocrystalline cCellulose-epoxy Composites Exhibiting Hierarchical Nacre-like Toughening by a team from Department of Mechanical Engineering, Massachusetts Institute of Technolog, Centre de Recherche Paul Pascal, CNRS, and MultiScale Material Science for Energy and Environment, CNRS-MIT
• 3D-Printed Electroactive Polymer Force-Actuator for Large and High Precise Optical Mirror Applications by a team primarily from INSA-Lyon, France
• Properties Regulation and Biological Applications of Decellularized Peripheral Nerve Matrix Hydrogel by a team from Sun Yat-sen University, Guangzhou, China
• Extrusion of AP Composite Propellant with Self-aligned Reactive Fibers by a team from Purdue University and University of Texas, San Antonio
• Additively Manufactured Reactive Material Architectures For Exothermic Brazing by a team from Vanderbilt University's School of Engineering
• Structure–Processing–Property Relationships of 3D Printed Porous Polymeric Materials by a team from various departments of the College of Engineering, Texas A&M University
• The Potential of Additively Manufactured Membranes for Selective Separation and Capture of CO2 by a team from the Department of Mining, Metallurgical, and Materials Engineering, University of the Philippines and Department of Chemical and Biomolecular Engineering and Joint Institute for Advanced Materials, University of Tennessee, Knoxville
• Sociotechnical Alignment in Biomedicine: The 3D Bioprinting Market beyond Technology Convergence by a team from University College London and University of Sussex
• Charge Transport in Electronic Devices Printed with Inks of Quasi-1D van der Waals Materials, by a team from University of California, Riverside and University of Nebraska, Lincoln
• Characterize Traction–separation Relation and Interfacial Imperfections by Data-driven Machine Learning Models by a team from Oak Ridge National Laboratory and the University of North Texas
• Rapid Heating and Chemical Speciation Characterization for Combustion Performance Analysis of Metallized, Nanoscale Thermites and Pvdfbound Solid Propellant Compositions, a PhD dissertation presented to the University of Maryland Department of Chemistry and Biochemistry
• Highly Recyclable, Mechanically Isotropic and Healable 3D-Printed Elastomers via Polyurea Vitrimers by a team from Oak Ridge National Laboratory's Chemical Sciences Division and Center for Nanophase Materials Sciences, and the Department of Chemical and Biomolecular Engineering of the University of Tennessee
• Extent of UV Curing in Highly Loaded Systems for Direct Ink Writing, an undergraduate paper submitted to Georgia Tech
• The innovative contribution of additive manufacturing towards revolutionizing fuel cell fabrication for clean energy generation: A comprehensive review by a team from Shenzhen University
• Effect of Operator Experience on Ability to Place Sequential, 2-mm-thick Increments of Composite by a team from the Department of Restorative Sciences, Dental College of Georgia at Augusta University
• Liquid Crystal-Mediated 3D Printing Process to Fabricate Nano-Ordered Layered Structures by a team from University of New South Wales, Leibniz Universität, Hannover, Monash University, RMIT University, Shinshu University, Tokida, and Centre de Recherche Paul Pascal−CNRS, University of Bordeaux
• 3D Printing of Flexible Composites via Magnetophoresis: Toward Medical Application Based on Low-Frequency Induction Heating Effect by a team from University of Lyon, INSA-Lyon, France
• Flexible 3D Printed Silicones for Gamma and Neutron Radiation Shielding by a team from Los Alamos National Laboratory, US Department of Energy's Kansas City National Security Campus, and Korea Institute of Science and Technology
• Persistent Polyamorphism in the Chiton Tooth: From a new Biomineral to Inks for Additive Manufacturing by a team from Materials Science and Engineering, Northwestern University and Advanced Photon Source, Sector 3, Argonne National Laboratory
• Direct Ink Writing of ZrB2-SiC Chopped Fiber Ceramic Composites by a team from the University of Tennessee, Knoxville, Georgia Institute of Technology, and Air Force Research Laboratory
• 3D Printing of Spent Coffee Ground Derived Biochar Reinforced Epoxy Composites by a team from Tuskegee University
• 3D Printing of Cellulose Nanocrystal-Loaded Hydrogels through Rapid Fixation by Photopolymerization by a team from the Hebrew University of Jerusalem and Politecnico di Torino
• Additive Manufacturing of Hetero-Magnetic Coupled Inductors by a team from Virginia Polytechnic Institute and State University
• On the Additive Manufacturing (3D Printing) of Viscoelastic Materials and Flow Behavior: From Composites to Food Manufacturing by a team from Case Western Reserve University, University of San Carlos, Philippines, Adamson University, Philippines, University of Tennessee, Knoxville, and Oak Ridge National Laboratory
• Recent trends in Natural Polysaccharide based Bioinks for Multiscale 3D Printing in Tissue Regeneration: A Review by a team from Tissue Engineering Laboratory, PSG Institute of Advanced Studies, Department of Polymer Science and Technology, Council of Scientific and Industrial Research - Central Leather Research Institute, and Biomaterial Surface Micro/Nanoengineering Laboratory, Colorado State University
• 3D Printable Magnesium-based Cements Towards the Preparation of Bioceramics by a team from Department of Chemistry “Ugo Schiff”, Università degli Studi di Firenze, Italy
• Carbohydrate Binding Module-Fused Antibodies Improve the Performance of Cellulose-Based Lateral Flow Immunoassays by a team including members from several laboratories and departments of the Technical University of Darmstadt and the Department of Biotechnology, Technical University of Braunschweig
• Thermal Energy Regulation with 3D Printed Polymer-Phase Change Material Composites by a team from the Department of Materials Science and Engineering, Texas A&M University and Department of Chemistry, Texas A&M University
• Computational Study of Extrusion Bioprinting with Jammed Gelatin Microgel-Based Composite Ink by a team from the Department of Mechanical and Aerospace Engineering, University of Florida and the School of Mechanical Engineering, Zhejiang University
• Recent Advances in 3D Printed Wound Dressings by a team from the University of Indonesia
• Multifunctional Reactive Nanocomposites via Direct Ink Writing by a team from Johns Hopkins University's Materials Science and Engineering Department and Hopkins Extreme Materials Institute, as well as The Charles Stark Draper Laboratory, Inc.
• Direct Ink Writing of Recyclable and in situ Repairable Photothermal Polyurethane for Sustainable 3D Printing Development by a team with members from several departments from The University of Western Ontario, as well as from the School of Mechatronic Engineering and Automation, Shanghai University
• Photopolymerizable Pullulan: Synthesis, Self-Assembly and Inkjet Printing by a team from CSGI & Department of Chemistry “Ugo Schiff”, Università degli Studi di Firenze, Italy
• Ultrathin and Ultrasensitive Printed Carbon Nanotube-Based Temperature Sensors Capable of Repeated Uses on Surfaces of Widely Varying Curvatures and Wettabilities by a team from Department of Mechanical Engineering, University of Maryland, College Park
• Moisture Sensitivity and Compressive Performance of 3D-Printed Cellulose-Biopolyester Foam Lattices by a team from School of Engineering, The University of Waikato, Centre for Advanced Composite Materials, The University of Auckland, and School of Design Innovation, Victoria University Wellington
• A Dual-Ink 3D Printing Strategy to Engineer Pre-Vascularized Bone Scaffolds In-Vitro by a team from several departments of the Oregon Health and Science University and the University of Geneva, University Clinic of Dental Medicine
• Niche-guided Tissue Patterning by Chemomechanical Flow Lithography, by a team from ARC Training Centre for Innovative BioEngineering, Embryology Unit, Children's Medical Research Institute, Sydney, School of Medical Science, Faculty of Medicine and Health, The University of Sydney, EMBL Australia, Single Molecule Science Node, School of Medical Sciences, UNSW, Sydney, and Department of Pharmacologyand Regenerative Medicine; Department of Bioengineering, University of Illinois at Chicago, Illinois

• Synthesis of Magneto-Responsive Microswimmers for Biomedical Applications by a team from Engineering and Natural Sciences, Bahcesehir University and Maritime Higher Vocational School, Piri Reis University

• Extrusion Increases the Mechanical Properties of 3D-Printable Nanocomposite Biomaterials, by a team from the Composite Biomaterial Systems Laboratory, Systems Design Engineering, University of Waterloo

• Synthetic Bone‐Like Structures Through Omnidirectional Ceramic Bioprinting in Cell Suspensions by a team from the University of New South Wales's Centre for Nanomedicine, School of Materials Science and Engineering, and School of Aerospace, Mechanical and Mechatronic Engineering

DIW/SEP/SSE, 2020

• Multi-Material Additively Manufactured Composite Reactive Materials via Condinuous Filament Direct Ink Writing by a team from The Mechanical Engineering Department of Vanderbilt University
• Designing 3D Printable Cementitious Materials with Gel-Forming Polymers by a team from the Departments of Chemical Engineering and Chemistry of Tennessee Technological University and the National Institute of Standards and Testing (NIST)
• A Dual Approach in Direct Ink Writing of Thermally Cured Shape Memory Rubber Toughened Epoxy by a team from the Department of Macromolecular Science and Engineering, Case Western Reserve University and the Department of Chemistry, Chulalongkorn University, Thailand
• Mechanics of Nozzle Clogging during direct ink writing of Fiber-Reinforced Composites by a team from the Materials and Manufacturing Directorate of the US Air Force Research Laboratoy, the University of Dayton Research Institute, the Mechanical, Aerospace, and Biomedical Engineering Department or the University of Tennessee and the Cornell High Energy Synchrotron Source
• Composite Hydrogels and their application for 3D Bioprinting in Regenerative Medicine by from the Medical University of Varna, Bulgaria
• Effects of Co3O4 Addition on Magnetic properties of NiCuZn Ferrite Feedstock for 3D-printing Power Magnetic Components by a team from Virginia Tech's Department of Materials Science and Engineering, Department of Electrical and Computer Engineering, and Center for Power Electronics Systems
• Ecofriendly Production of Bioactive Tissue Engineering Scaffolds Derived from Egg- and Sea-shells by a team from the Department of Material Science and Engineering and the Department of Pathobiology, College of Veterinary Medicine, Nursing and Allied Health of Tuskegee University
• Direct Ink Writing of a Light‐Responsive Underwater Liquid Crystal Actuator with Atypical Temperature‐Dependent Shape Changes by a team from the Stimuli-responsive Functional Materials & Devices (SFD) Group of the Department of Chemical Engineering and Chemistry of Eindhoven University of Technology
• Silk Fibroin Reactive Inks for 3D Printing Crypt-like Structures by a team from the Polymer Program, Institute of Materials Science, University of Connecticut and the Chemical and Biomolecular Engineering, University of Connecticut
• Additive-Free Carbon Particle Dispersions, Pastes, Gels, and Doughs a patent application from the Department of Molecular Biosciences of Northwestern University
• Development of 3D-Printed Layered PLGA Films for Drug Delivery and Evaluation of Drug Release Behaviors by a team from the School of Pharmacy and Health Sciences, Fairleigh Dickinson University
• 3D Printing of Cytocompatible Gelatin‐Cellulose‐Alginate Blend Hydrogels by a team from the Engineering departments of Koç University and Bahcesehir University, both in Turkey
• Effects of SiO2 Inclusions on Sintering and Permeability of NiCuZn Ferrite for Additive Manufacturing of Power Magnets by a multi-disciplinary team from Virginia Tech
• Transparent Alumina Ceramics Fabricated by 3D Printing and Vacuum Sintering by a team from the Kazuo Inamori School of Engineering, New York State College of Ceramics, Alfred University, Alfred, NY
• Additive Manufacturing and Characterization of AgI and AgI–Al2O3 Composite Electrolytes for Resistive Switching Devices, a paper from the US Air Force Research Laboratory using a Nordson head on a Hyrel printer.
• Additively Manufactured Thermite-based Energetics: Characterization and Applications, a PhD dissertation submitted to the Mechanical Enginnering Department of Vanderbilt University
• Effect of Sterilization Treatment on Mechanical Properties, Biodegradation, Bioactivity and Printability of GelMA Hydrogels (in Tissue Engineering) by a team from the Composite Biomaterial Systems Laboratory of the University of Waterloo
• Impact of Filler Composition on Mechanical and Dynamic Response of 3-D Printed Silicone-based Nanocomposite Elastomers using a Nordson Ultimus™ V dispenser on Hyrel equipment, by a team from Los Alamos National Laboratory, Sandia National Laboratory, and Department of Energy Engineering, Gyeongnam National University of Science and Technology (South Korea)
• Fabrication and Characterization of Fe₁₆N₂ Micro‐Flake Powders and Their Extrusion Based 3D Printing into Permanent Magnet Form by a multi-disciplinary, multi-university team from Istanbul, Turkey
• Cement-Based Direct Ink for 3D Printing of Complex Architected Structures , a patent application by a team including members of Department of Materials Science and NanoEngineering, Rice University
• Reactive 3D Printing of Shape Programmable Liquid Crystal Elastomer Actuators by a team from the Department of Materials Science and NanoEngineering of Rice University
• Injectable Gelatin Microgel-based Composite Ink for 3D Bioprinting in Air by a team from the University of Florida's Biomedical Engineering Department
• Enabling Compact GTL by 3D-Printing of Structured Catalysts by a team from The University of Queensland's School of Chemical Engineering and Australian Institute for Bioengineering and Nanotechnology and also by The Australian Petroleum International Exploration and Development (APIED)
• Bio-Ink Structures and Methods of Producing the Same, a patent application by Lawrence Livermore National Laboratory
• 3D Printing of Transparent YAG Ceramics using Copolymer-Assisted Slurry by a team from The New York State College of Ceramics at Alfred University
• On Design for Additive Manufacturing (DAM) Parameter and Its Effects on Biomechanical Properties of 3D Printed Ceramic Scaffolds by a team mostly from Australian Universities.
• All 3D-printed Stretchable PiezoElectric NanoGenerator (PENG) with Non-protruding Kirigami Structure by a team from The School of Materials Science and Engineering, Nanyang Technological University and Singapore-HUJ Alliance for Research and Enterprise (SHARE), Nanomaterials for Energy and Water Nexus (NEW), Campus for Research Excellence and Technological Enterprise (CREATE)
• Opportunities and Challenges of 3D-Printed Pharmaceutical Dosage Forms by Adam Procopio from Merck Pharmceuticals
• Experimental Observation of the Heat Transfer Mechanisms that drive Propagation in Additively Manufactured Energetic Materials by a team from the Department of Chemical and Environmental Engineering, University of California, Riverside and the Department of Chemical and Biomolecular Engineering, University of Maryland, College Park
• 3D Printable Magnesium Oxide Concrete: Towards Sustainable Modern Architecture by a team from New York University, Abu Dhabi
• Soldered Copper Lap Joints using Reactive Material Architectures as a Heat Source by a team from the Department of Mechanical Engineering, Vanderbilt University
• Combustion of 3D Printed 90 WT% Loading Reinforced Nanothermite by a team from the Department of Chemical and Environmental Engineering, University of California, Riverside and the Department of Chemical and Biomolecular Engineering, University of Maryland, College Park
• Photocurable Pentaerythritol Triacrylate/Lithium Pphenyl‐2,4,6‐trimethylbenzoylphosphinate‐based Ink for Extrusion‐based 3D Printing of Magneto‐responsive Materials by a team from Bahçeşehir University, Piri Reis University, and Sabanci University in Istanbul
• Spatially Focused Microwave Ignition of Metallized Energetic Materials, by a team from the Engineering Departments of University of California, Riverside and the University of Maryland.
• Additive Manufacturing with Strontium Hexaferrite-Photoresist Composite by a team from several departments at The University of California, Los Angeles (UCLA)
• Early-Age Performance of 3D Printed Carbon Nanofiber and Carbon Microfiber Cement Composites by a team from the Department of Civil and Environmental Engineering, Vanderbilt University
• Cross-linkable Microgel Composite Matrix Bath for Embedded Bioprinting of Perfusable Tissue Constructs and Sculpting of Solid Objects by a team from the University of Florida's Biomedical Engineering Department

DIW/SEP/SSE, 2019

• Graphene Foam-Reinforced Shape Memory Polymer Epoxy Composites, a PhD paper submitted to Florida International University
• Biodegradable Polymer Blends for Food Packaging Applications, a chapter in "Food Packaging: Innovations and Shelf-Life", by a team from The Department of Materials Science and Engineering of Tuskegee University
• Analysis of Free Chlorine in Aqueous Solution at Very Low Concentration with Lateral Flow Tests by TU Darmstadt
• Intrinsic Thermal Desorption in a 3D Printed Multi-Functional Composite CO2 Sorbent with Embedded Heating Capability by a team from the Boulder Experimental Electronics and Manufacturing Laboratory of the University of Colorado, Boulder
• 3D Printing an Electrode of Living Bacteria by a team from Department of Chemistry and Biochemistry, University of CaliforniaSanta Cruz
• Ignition and Combustion Analysis of Direct Write Fabricated Aluminum/Metal Oxide/PVDF Films, by a team from the Engineering Departments of University of California, Riverside and the University of Maryland.
• Hydroxyapatite Structures Created by Additive Manufacturing with Extruded Photopolymer by a team from the Colorado State University College of Engineering
• Rheological Considerations for Binder Development in Direct Ink Writing of Energetic Materials by a team from the School of Materials Science and Engineering (MSE) at Georgia Tech
• 3D Printed Layer of Polyaniline-Based Conductive Polymer for Lightning Strike Protection of Carbon Fiber Reinforced Plastics (CFRPs) by a team from Oak Ridge National Laboratory
• Bioprinting Technologies in Tissue Engineering, part of the Advances in Biochemical Engineering/Biotechnology book series.
• 3D-Printability of Aqueous poly(ethylene oxide)(PEO) Gels by a team primarily from the Faculty of Medicine, University of Tartu, Estonia
• A New Approach to 3D Printing Dense Ceramics by Ceramic Precursor Binders by Prof. Shlomo Magdassi's group at The Hebrew University of Jerusalem
• Additive Manufacturing of 3D Structures Composed of Wood Materials by Prof. Shlomo Magdassi's group at The Hebrew University of Jerusalem
• Three-Dimensional Printing Control, a patent application by a team from Chromatic 3D Materials
• Methods and systems for precision application of agents to a target surface, a patent application by a team from Procter & Gamble
• hBN-Acrylate Composite Printing: Stereolithography and UV-Assisted Direct Write, a Masters' Thesis from the University of Connecticut
• Printability of Methacrylated Gelatin upon Inclusion of a Chloride Salt and Hydroxyapatite Nano‐Particles by a team from the Composite Biomaterial Systems Laboratory, Systems Design Engineering, University of Waterloo
• Extremely Stretchable and Self-Healing Conductor Based on Thermoplastic Elastomer for All-Three-Dimensional Printed Triboelectric Nanogenerator by a team from The School of Materials Science and Engineering, Nanyang Technological University and Singapore-HUJ Alliance for Research and Enterprise (SHARE), Nanomaterials for Energy and Water Nexus (NEW), Campus for Research Excellence and Technological Enterprise (CREATE)
• Printing Therapeutic Proteins in 3D using Nanoengineered Bioink to Control and Direct Cell Migration by a team by a team from Texas A&M University.
• Bactericidal Activity of 3D-printed Hydrogel Dressing Loaded with Gallium Maltolate by a team from the Department of Biomedical Engineering, Texas A&M University
• Extrudable Hydroxyapatite / Plant Oil-based Biopolymer Nanocomposites for Biomedical Applications: Mechanical Testing and Modeling by a team from The Systems Design Engineering Department of The University of Waterloo, Canada
• 3D Printed Multifunctional, Hyperelastic Silicone Rubber Foam by a team from the Macromolecular Science & Engineering Department of Case Western Reserve University
• Extrusion Printing of Liquid Crystal Elastomers, a patent application by a team from the Bioengineering Department of the University of Texas, Dallas
• Tailoring a Silver Paste for Additive Manufacturing of Co-Fired Ferrite Magnetic Components by a team from Virginia Tech
• 3D Printing of a Thermo- and Solvatochromic Composite Material Based on a Cu(II)–Thymine Coordination Polymer with Moisture Sensing Capabilities by a team from Nanyang Technological University (Singapore) and the Hebrew University of Jerusalem)
• Advancing Frontiers in Bone Bioprinting, by a team primarily from The University of California at Los Angeles
• Direct Writing of Tunable Living Inks for Bioprocess Intensification in ACS's Nano Letters
• Gellan Fluid Gel as a Versatile Support Bath Material for Fluid Extrusion Bioprinting by a team from the University of Florida's Biomedical Engineering Department
• Microwave Control of Composite Solid Propellant Flame Spread Through Eddy Current Heating of Wired/Foiled Propellant by a team from Iowa State University's Mechanical Engineering Department
• Developments of 3D polycaprolactone/beta-tricalcium phosphate/collagen Scaffolds for Hard Tissue Engineering by a multi-disciplinary, multi-university team from Istanbul, Turkey
• 3D Printing of Poloxamer 407 Nanogel Discs and Their Applications in Adjuvant Ovarian Cancer Therapy by a team from the St. Louis College of Pharmacy

DIW/SEP/SSE, 2018

• Nano Silica-Carbon-Silver Ternary Hybrid Induced Antimicrobial Composite Films for Food Packaging Application by a team from the Materials Science & Enginnernig Department of Tuskegee University
• Additive Manufacturing of Alumina Components by Extrusion of in-situ UV-Cured Pastes by a team from Sandia National Laboratory and The University of New Mexico's Center for MicroEngineered Materials
• Hydrocolloid Architectural Design of 3D Printed Scaffolds Controls the Volume and Functionality of Newly Formed Bone by a team from the School of Aerospace, Mechanical and Mechatronic Engineering, University of Sydney and the School of Chemistry, University of New South Wales, Sydney
• Hydrocolloid Inks for 3D Printing of Porous Hydrogels by a team with members from The Department of Biomedical Engineering, Texas A&M University, The Department of Biomedical Engineering, University of Texas at Austin, and The Department of Chemical and Materials Engineering, New Mexico State University
• Improved In Situ Seeding of 3D Printed Scaffolds using Cell-Releasing Hydrogels by a team with members from The Department of Biomedical Engineering, Texas A&M University, The Department of Biomedical Engineering, University of Texas at Austin, and The Department of Bioengineering, Rice University.
• Effect of Silk-Based Hydrogel Topography on Intestinal Epithelial Cell Morphology and Wound Healing In Vitro a thesis by Marisa E. Boch from the Department of Chemical and Biomolecular Engineering at the University of Connecticut
• Compressible, Thermally Insulating, and Fire Retardant Aerogels through Self-Assembling Silk Fibroin Biopolymers Inside a Silica Structure - An Approach towards 3D Printing of Aerogels by a team from the Chemistry and Physics of Materials Department of The University of Salzburg and School of Inorganic Chemistry at The University of Cologne.
• Covalent-Supramolecular Hybrid Polymers as Muscle-Inspired Anisotropic Actuators by an interdisciplinary team from Northwestern University. The 3D printing experiments were supported by the Air Force Research Laboratory under agreement number FA8650-15-2-5518
• Fully 2D and 3D Printed Anisotropic Mechanoluminescent Objects and their Application for Energy Harvesting in the Dark by Prof. Shlomo Magdassi's group at The Hebrew University of Jerusalem.
• Additive-free Carbon Nanotube Dispersions, Pastes, Gels, and Doughs in Cresols by a team from Northwestern University
• 3D Printing of Hierarchical Porous Silica and α‐Quartz by a team from The University of Salzburg
• Polymeric Materials and Articles Manufactured There From by a team from Procter and Gamble
• UV-curable Ferrite Paste for Additive Manufacturing of Power Magnetics by a team from Virginia Tech
• Tailoring the Porosity and Microstructure of Printed Graphene Electrodes via Polymer Phase Inversion by a team from Northwestern University

DIW/SEP/SSE, 2017

• Injectable Nanocomposite Hydrogels for Cell Delivery and Bioprinting by a team by a team from three disciplines of Texas A&M University.
• Feasibility of Printing 3D Bone Models for Education at TUCVM at ResearchGate
• Design and Additive Manufacturing of Multi-Permeability Magnetic Cores, by a team from Virginia Tech
• Combustion-Assisted Photonic Annealing of Printable Graphene Inks via Exothermic Binders, by a team from Northwestern Univeristy
• In Vitro Evaluation of 3D Bbioprinted Tri-Polymer Network Scaffolds for Bone Tissue Regeneration, by a team from The University of Connecticut
• Enabling Process Intensification via 3D Printing of Catalytic Structures by a team from University of Queensland
• 3D Bioprinting for Musculoskeletal Applications by Alexander Popov, Sara Malferrari, & Deepak M Kalaskar in Future Medicine
• UV-assisted 3D-printing of Soft Ferrite Magnetic Components for Power Electronics Integration by Dr. Y. Yan (and others), Virginia Tech
• Alginate Hydrogels for Bone Tissue Regeneration by Stephanie T. Bendtsen of The University of Connecticut
• Fabrication of Biomimetic Bone Grafts with Multi-Material 3D Printing by Nicholas Sears et. al., of the Biomedical Engineering Department of Texas A&M University.
• Nanoengineered Eggshell–Silver Tailored Copolyester Polymer Blend Film with Antimicrobial Properties by a team from Tuskegee University
• Design Methodology and Materials for Additive Manufacturing of Magnetic Components - PhD Thesis of Y. Yan, Virginia Tech

DIW/SEP/SSE, 2016

• High Performance, 3D-Printable Dielectric Nanocomposites for Millimeter Wave Devices by a team from the Lincoln Laboratory at the Massachusetts Institute of Technology (MIT)
• Additive Manufacturing of Magnetic Components for Heterogeneous Integration by Dr. Y. Yan (and others), Virginia Tech
• Bioprinting Defined Heterogeneous Cellular Microenvironments from The Biomaterials and Tissue Engineering Research Unit of the Aerospace, Mechanical and Mechatronic Engineering Department of The University of Sydney
• Design and Fabrication of 3D Printed Scaffolds with a Mechanical Strength Comparable to Cortical Bone to Repair Large Bone Defects in Nature.com's Scientific Reports
• Emulsion Inks for 3D Printing of High Porosity Materials in the Macromolecular Journals
• 3D Printed Energetics by the Weapons and Combat Systems Division of the Australian Department of Defense

DIW/SEP/SSE, 2015

• 3D Printing of High Porosity, Biodegradable Foams with Cure on Dispense - Presentation by Elizabeth Cosgriff-Hernández of Department of Biomedical Engineering, Texas A&M University
• Graduate Abstract: Dynamic increase in matrix stiffness promotes invasive tumor phenotype in vivo from multiple organizations, at BioMaterials.org
• Die-Less MIM-style Additive Manufacturing with Controlled Porosity: A Proof of Concept by the Department of Materials Science and Engineering of Lehigh University
• Bioactive Nanoengineered Hydrogels for Bone Tissue Engineering: A Growth-Factor-Free Approach in The American Chemical Society's ACS Nano

DIW/SEP/SSE, 2014

• Development of 3D printed Ceramic scaffolds for Treatment of Segmental Bone Defects from The Biomaterials and Tissue Engineering Research Unit of the Aerospace, Mechanical and Mechatronic Engineering Department of The University of Sydney

Heated Reservoir Printing (DPE, HME)

Also known as DPE (Direct Powder Extrusion) or HME (Hot Melt Extrusion).

DPE, HME 2023

• Combination Techniques Towards Novel Drug Delivery Systems Manufacturing: 3D PCL Scaffolds Enriched With Tetracycline-loaded PVP Nanoparticles by a team from Marmara University, Turkey
• Fully Recyclable Cured Polymers for Sustainable 3D Printing by a team from the Department of Polymer Materials Engineering, Pernick Faculty of Engineering, Shenkar College, Israel and the Institute of Chemistry and Center for Nanoscience and Nanotechnology, The Hebrew University of Jerusalem
• Three-Dimensional Printing Parameter Optimization for Salmon Gelatin Gels Using Artificial Neural Networks and Response Surface Methodology: Influence on Physicochemical and Digestibility Properties by a team from Department of Agricultural, Food and Nutritional Science, University of Alberta,, Department of Food Science and Chemical Technology, Universidad de Chile,, and the Department of Food Engineering and the Department of Basic Sciences, Universidad del Bío-Bío, Chile
• Production of Essential Oil Coated Polycapralactone Scaffold With Antibacterial Properties by an author from Marmara University, Istanbul
• Geometry, Mechanics and Actuation of Intrinsically Curved Folds by a team from Department of Engineering, University of Cambridge, Cambridge, UK
• Fabrication of Avian Eggshell Membrane Derived Dispersed Collagen Hydrogels for Potential Bone Regeneration by a team from Indian Institute of Technology, Delhi
• Toward Fully Printed Soft Actuators: UV-Assisted Printing of Liquid Crystal Elastomers and Biphasic Liquid Metal Conductors by a team from the Institute of Systems and Robotics Department of Electrical and Computer Engineering University of Coimbra
• Controlled Directionality in 3D Printing of Graphite-Reinforced Polymer Composite with Enhanced Mechanical Properties by a team from the Indian Institute of Technology's Kharagpur and Gandhinagar campuses, and the Carbon Science Centre of Excellence, Morgan Advanced Materials, Penn State University
• 3D Printed Hierarchical Porous Poly(ε-caprolactone) Scaffolds from Pickering High Internal Phase Emulsion Templating by a team from the Department of Textile and Fibre Engineering, Indian Institute of Technology, Delhi
• Do we need perfect mixing between fuel and oxidizer to maximize the energy release rate of energetic nanocomposites? by a team from the Department of Chemical and Environmental Engineering, University of California, Riverside and the Department of Mechanical Engineering, Stanford University

DPE, HME 2022

• 3D Printing of Liquid Metal Embedded Elastomers for Soft Thermal and Electrical Materials by a team from Carnegie Mellon University's Mechanical and Chemical Engineering Departments; the Department of Mechanical and Automation Engineering, Chinese University of Hong Kong, and the Department of Mechanical Engineering, Seoul National University
• Robotic Pick-and-Place Operations in Multifunctional Liquid Crystal Elastomers by a team from Eindhoven University of Technology's Institute for Complex Molecular Systems and Department of Chemical Engineering and Chemistry, the Instituto de Nanociencia y Materiales de Aragón (INMA)Departamento de Física de la Materia CondensadaCSIC-Universidad de Zaragoza, the CIBER in Bioengineering, Biomaterials and Nanomedicine, and the [ SCNU-TUE Joint Lab of Device Integrated Responsive Materials (DIRM), National Center for International Research on Green Optoelectronics, South China Normal University]
• Development of Embeddable Additive Manufacturing Microsensors for Structural Health Monitoring, by a team from Embry-Riddle Aeronautical University
• Continuous, Non-Destructive Detection of Surface Bacterial Growth with Bioinspired Vascularized PolymersGrowth with Bioinspired Vascularized Polymers, submitted to the University of Maine in pursuit of a Master of Science in Biomedical Engineering
• A Novel Dynamic Polymer Synthesis via Chlorinated Solvent Quenched Depolymerization by a team from Oak Ridge National Laboratory's Chemical Services Division and Center for Nanophase Materials Sciences; University of Tennessee, Knoxville's Department of Chemistry and Department of Chemical and Biomolecular Engineering; and Beijing University of Chemical Technology
• Alginate–Sodium Sulfate Decahydrate Phase Change Composite with Extended Stability by a team from Chemical Sciences Division, Oak Ridge National Laboratory, Building and Transportation Sciences Division, Oak Ridge National Laboratory, and the Department of Chemistry, University of Tennessee, Knoxville
• Continuous, Non-Destructive Detection of Microorganism Growth at Buried Interfaces with Vascularized Polymers by a team from the Biomedical Science and Engineering, University of Maine, the Department of Mechanical Engineering and Material Science, Duke University, and the [Pritzker School of Molecular Engineering, University of Chicago https://pme.uchicago.edu/]
• Comparing the Cpabilities of Vibration-Assisted Printing (VAP) and Direct-Write Additive Manufacturing Techniques by a team from Purdue University and Naval Postgraduate School
• Characterization of Micro-Sandwich Structures via Direct Ink Writing Epoxy Based Cores by a team from various engineering departments at The University of Tennessee, Knoxville
• Emulsion Templated Porous Funnel from Polypropylene Waste for Efficient Oil Separation and Spillage Management by a team from the Department of Textile Technology, Indian Institute of Technology - Delhi
• Material Synthesis and Machine Learning for Additive ManufacturingManufacturing, a Master's Thesis submitted to the Department of Aerospace and Mechanical Engineering, University of Texas at El Paso
• Material Synthesis and Additive Manufacturing of Ceramics, a Master's Thesis submitted to the Department of Aerospace and Mechanical Engineering, University of Texas at El Paso
• Cholesteric Liquid Crystals in Additive Manufacturing, a doctoral dissertation submitted to the Laboratory of Stimuli-Responsive Functional Materials and Devices (SFD), Department of Chemical Engineering and Chemistry, Eindhoven University of Technology (TU/e)
• Development of Advanced 3D-Printed Solid Dosage Pediatric Formulations for HIV Treatment by a team from Trinity College Dublin, Complutense University of Madrid, and King Abdulaziz University
• An Additive Manufacturing-based 3D Printed Poly ɛ-CaproLactone (PCL) / Alginate Sulfate / Cxtracellular Matrix Construct for Nasal Cartilage Regeneration, by a team from Texas A&M International University, Iran University of Medical Sciences, and the University of Tehran

DPE, HME 2021

• Effects of Crosslinking on the Physical Solid-State and Dissolution Properties of 3D-printed Theophylline Tablets by a team from the Institute of Pharmacy and the Institute of Biomedicine and Translational Medicine of the University of Tartu and from the Division of Pharmaceutical Chemistry and Technology, Faculty of Pharmacy, University of Helsinki
• Understanding Direct Powder Extrusion for Fabrication of 3D Printed Personalised Medicines: A Case Study for Nifedipine Minitablets, a study by a team from the Department of Pharmaceutics and Food Science, Facultad de Farmacia, Universidad Complutense de Madrid,and the Biomaterials, Bio-Engineering and Nanomedicine (BioN) Lab, Institute of Biomedical and Biomolecular Sciences, School of Pharmacy and Biomedical Sciences, University of Portsmouth
• Printable Elastomeric Electrodes with Sweat‑Enhanced Conductivity for Wearables by a team primarily from Nanyang Technological University, Singapore
• Fabrication and Testing of Advanced Composites for Extreme Environments, a Master's dissertation submitted to the Mechanical Engineering Department of Texas A&M University
• Wound Healing: From Passive to Smart Dressings by a team from Department of Biomedical Engineering, Amirkabir University of Technology, Tehra and UQ Diamantina Institute, Translational Research Institute, The University of Queensland
• 3D Printing of Polyvinylidene Fluoride Based Piezoelectric Nanocomposites: An Overview by a tea, from Eskişehir Technical University, Turkey
• 3D Printing Compositesfrom Raw Materials, a Master Thesis submitted to Lund University
• Soft Elasticity Optimises Dissipation in 3D-Printed Liquid Crystal Elastomers by a team from the Department of Mechanical Engineering, University of Colorado, Denver, School of Physics and Astronomy, University of Leeds, Materials and Failure Modeling Department, Sandia National Laboratories, and Impressio, Inc.
• 3D-Printed Enzyme-Embedded Plastics by a team from Scion, a Crown Research Institute in New Zealand

DPE, HME 2020

• Study of Recyclable and Repairable Dynamic Covalent Polymers for Sustainable 3D Printing Development for Sustainable 3D Printing Development, a thesis for a PhD in Mechanical and Materials Engineering submitted to The University of Western Ontario
• Toward Multifunctional Liquid Metal Composites, a video by a team from the Department of Mechanical Engineering, Carnegie Mellon University
• Controlled Assembly of Liquid Metal Inclusions as a General Approach for Multifunctional Composites by a team from the Department of Mechanical Engineering, Carnegie Mellon University
• Syngas to Higher Alcohols Synthesis over 3D Printed KMoCo/ZSM5 Monolith by a team from the Australian Institute for Bioengineering and Nanotechnology (AIBN) of The University of Queensland
• Extrusion 3D Printing of Porous Silicone Architectures for Engineering Human Cardiomyocyte-Infused Patches Mimicking Adult Heart Stiffness by a team from the Department of Mechanical and Materials Engineering of Florida International University
• Temperature and Solvent Facilitated Extrusion Based 3D Printing for Pharmaceuticals by a team from School of Pharmacy and Biomedical Sciences, University of Central Lancashire
• 3D Printed Food and Customized Silicone Molds: Investigating Aesthetic Appearance and Food Preparing Methods for a Dysphagia Diet, a Master's paper submitted to the Mechanical Engineering Department of Halmstad University of Sweden
• Inkjet-Printed Iontronics for Transparent, Elastic, andStrain-Insensitive Touch Sensing Matrix by a team from the School of Materials Science and Engineering at Nanyang Technological Univeristy and University of Electronic Science and Technology of China
• Mechanical Properties of Nanocomposite Biomaterials improved by extrusion during Direct Ink Writing by a team from the Composite Biomaterial Systems Laboratory of the Systems Design Engineering School at the University of Waterloo, Canada

DPE, HME 2019

• Vascularized Polymers Spatially Control Bacterial Cells on Surfaces by a team from the Department of Chemical and Biomedical Engineering, University of Maine
• Dynamically Crystalizing Liquid‐Crystal Elastomers for an Expandable Endplate‐Conforming Interbody Fusion Cage by a team from the College of Engineering, Design and Computing, University of Colorado Denver
• Development of an Open-Sourced Automated Ultrasonic-Assisted Soldering System, by a team from the Department of Mechanical Engineering of Clemson University
• Acoustic Analysis of Ultrasonic Assisted Soldering for Enhanced Adhesion, by a team from the Department of Mechanical Engineering of Clemson University
• Preparation and Applications of Stimuli-Responsive Composite Materials, a PhD dissertation from the Case Western Reserve University Department of Chemistry.
• In-operando High-speed Microscopy and Thermometry of Reaction Propagation and Sintering in a Nanocomposite by a team from the Department of Chemical and Environmental Engineering, University of California, Riverside and the Department of Chemical and Biomolecular Engineering, University of Maryland, College Park
• Comparison study of the ignition and combustion characteristics of directly-written Al/PVDF, Al/Viton and Al/THV composites by a team from the Department of Chemical and Biomolecular Engineering and Department of Chemistry and Biochemistry, University of Maryland
• A Proof of Concept for 3D Printing of Solid Lipid-Based Formulations of Poorly Water-Soluble Drugs to Control Formulation Dispersion Kinetics by a team including the University College London School of Pharmacy
• Architecture can Significantly Alter the Energy Release Rate from Nanocomposite Energetics by a team from University of Maryland's Dept. of Physics
• Comparative Characterization of the Hydrogel Added PLA/β-TCP Scaffolds Produced by 3D Bioprinting by a team from Marmara University, Turkey
• 3D Printing of Thermoreversible Polyurethanes with Targeted Shape Memory and Precise In-Situ Self-Healing Properties by Yue Zhang, Xiangyu Yin, Mingyue Zheng, Carolyn Moorlag, Jun Yang and Zhonglin Wang.
• Additive Processing of Fluoroelastomers, a patent application by a team from 3M
• Additive Processing of Fluoropolymers, a patent application by a team from 3M

DPE, HME 2018

• 3D Printing of Surgical Hernia Meshes Impregnated with Contrast Agents: In Vitro Proof of Concept with Imaging Characteristics on Computed Tomography by a team from Washington University in St. Louis
• Composites of Fatty Acids and Ceramic Powders are Versatile Biomaterials for Personalized Implants and Controlled Release of Pharmaceuticals by a team from The University of Southern Denmark
• Extrusion-Based 3D Printing of Poly (ethylene glycol) Diacrylate Hydrogels Containing Positively and Negatively Charged Groups by a team from the University of Stuttgart and the Fraunhofer Institute, in Stuttgart, Germany
• Nanoengineered Colloidal Inks for 3D Bioprinting in The American Chemical Society's Langmuir

DPE, HME 2017

• Shear-Thinning and Thermo-Reversible Nanoengineered Inks for 3D Bioprinting in the American Chemical Society's Applied Materials & Interfaces Journal
• Influence of Shear Thinning and Material Flow on Robotic Dispensing of PEG in The American Chemical Society's ACS Nano

Filament Printing (FFF, FDM)

Also known as FFF (Fused Filament Fabrication) or FDM (Fused Deposition Modeling).

FDM/HFF, 2023

• 3D Printable Spatial Fractal Structures Undergoing Auxetic Elasticity by a team from Harbin Institute of Technology, Nanyang Technological University, City University of Hong Kong, and Northumbria University
• The Effect of Porosity on Flexoelectricity in 3d Printed Aluminum/polyvinylidene Fluoride Composite by a team from Purdue University
• Effect of Input Variables on the Mechanical Properties of Additively Manufactured PEEK Thermoplastics by a team from Department of Mechanical Engineering, École de Technologie Supérieure, Montréal, Institut Clément Ader, UMR CNRS 5312, University of Toulouse, and Department of Mechanical Engineering, Innovations Institute in Ecomaterials, Ecoproducts and Ecoenergy (I2E3), Université du Québec à Trois-Rivières
• A Novel Feature Representation Method Based on Similarity Between Statistical Distributions of Acoustic Emission Waveforms by a team from College of Logistics Engineering, Shanghai Maritime University, Shanghai, China and College of Mechanical Engineering, State Key Laboratory of Fluid Power Transmission and Control, Zhejiang University, Hangzhou, China
• Process Monitoring and Control of Advanced Manufacturing based on Physics-Assisted Machine Learning, a dissertation submitted to the Industrial and Systems Engineering department of Virginia Tech
• Multimodal Origami Shape Memory Metamaterials Undergoing Compression-twist Coupling by a team from Harbin Institute of Technology, China, School of Mechanical and Aerospace Engineering, Nanyang Technological University, and Northumbria University, UK
• Process Parameter Optimization for Reproducible Fabrication of Layer Porosity Quality of 3D-Printed Tissue Scaffold by a team from several departments at Virginia Tech
• Fundamentals of Crystalline Evolution and Properties of Carbon Nanotube-Reinforced Polyether Ether Ketone Nanocomposites in Fused Filament Fabrication by a team from several departments at Texas A&M University
• Printed Planar Microwave Connector with Multiple Signal Lines by a team from Electrical & Computer Engineering, University of Massachusetts, Lowell
• Structured 3D Printed Dry ECG Electrodes Using Copper Based Filament by a team from the Computer Electrical Mathematical Science and Engineering Division, King Abdullah University of Science and Technology (KAUST)
• 3D Printed Dry Electrodes for Electrophysiological Signal Monitoring: A Review by a team from King Abdullah University of Science and Technology (KAUST)

FDM/HFF, 2022

• A Comparison Between Large-format 3d Printing and Conventional Fused Filament Fabrication by a team from Universidad Autónoma de Occidente, Columbia
• Imbalanced Data Classification via Generative Adversarial Network with Application to Anomaly Detection in Additive Manufacturing Process by a team from the Grado Department of Industrial and Systems Engineering, Virginia Tech and the Department of Mechanical and Industrial Engineering, New Jersey Institute of Technology
• Reinforcement Learning-based Defect Mitigation for Quality Assurance of Additive Manufacturing by a team from the Grado Department of Industrial and Systems Engineering, Virginia Tech and the Department of Mechanical and Industrial Engineering, New Jersey Institute of Technology
• Fabrication of Polycarbonate Filaments Infused with Carbon from Coconut Shell Powder for 3D Printing Applications by a team from Tuskegee University's Department of Materials Science and Engineering (MSE)
• Smart Quality Assurance System for Additive Manufacturing using Data-driven based Parameter-Signature-Quality Framework, a dissertation submitted to Virginia Tech's Industrial and Systems Engineering department
• Tunable Hyperbolic Out-Of-Plane Deformation of 3D-Printed Auxetic PLA Shape Memory Arrays by a team from the Harbin Institute of Technology, China and Nanyang Technological University, Singapore
• Closed-loop Additive Manufacturing of Upcycled Commodity Plastic through Dynamic Cross-linking by a team from the Chemical Sciences Division and Materials Sciences and Technology Division of Oak Ridge National Laboratory and the Bredesen Center for Interdisciplinary Research and Graduate Education, University of Tennessee, Knoxville
• Effective Reinforcement of Engineered Sustainable Biochar carbon for 3D Printed Polypropylene Biocomposites by a team from Tuskegee Univeristy
• Nonparametric Bayesian Framework for Material and Process Optimization with Nanocomposite Fused Filament Fabrication by a team from the departments of Industrial and Systems Engineering and Chemical Engineering of Auburn University
• Paliperidone Palmitate as Model of Heat-Sensitive Drug for Long-Acting 3D Printing Application by a team from the Laboratory of Pharmaceutics and Biopharmaceutics and the Laboratory of Polymer and Soft Matter Dynamics of the Université libre de Bruxelles and the Laboratory of Polymeric and Composite Materials (LPCM), Center of Innovation and Research in Materials and Polymers (CIRMAP), University of Mons
• Effect of infill on resulting mechanical properties of additive manufactured bioresorbable polymers for medical devices by a team from Poly-Med, Inc. and Clemson University
• Surface Design of 3D-printed PEEK by Controlling Slicing Parameters in the International Journal of Mechanical Engineering and Robotics Research

FDM/HFF, 2021

• Effective Reinforcement of Engineered Sustainable Biochar Carbon for 3D Printed Polypropylene Biocomposites from a team from Tuskegee University
• Fabrication and Characterization of Polycarbonate-Silica Filaments for 3D Printing Applications by a team from Tuskegee University
• Sequentially Tunable Buckling in 3D Printing Auxetic Metamaterial Undergoing Twofold Viscoelastic Resonances, by a team from Harbin Institute of Technology, China, Northwestern Polytechnical University, China, and School of Mechanical and Aerospace Engineering, Nanyang Technological University, Singapore
• Synthesis and Characterization of Functiona Materials for 3D Printed Composites, a Master's thesis submitted to the Mechanical Engineering Department of Texas A&M University
• Novel Architected Material for Cardiac Patches by a team from the Department of Mechanical Engineering, University of Texas at San Antonio
• Boron Nitride Nanotubes for Heat Dissipation in Polycaprolactone Composite by a team from Department of Chemistry, Duke University and Université Grenoble Alpes
• 3D Printing of Supramolecular Polymer Hydrogels with Hierarchical Structure by a team from Northwestern University's Department of Materials Science and Engineering and Simpson Querrey Institute and the Soft Materials Branch of the Materials and Manufacturing Directorate, Air Force Research Laboratory

FDM/HFF, 2020

• Physics Based Compressive Sensing for Additive Manufacturing Process Monitoring a PhD dissertation presented to the Mechanical Engineering School at Georgia Tech.
• Preparation and Characterization of Hot-Melt Extruded Polycaprolactone-Based Filaments Intended for 3D-Printing of Tablets by a team from the Institute of Pharmacy, Department of Immunology, and the Department of Geology of the University of Tartu, Estonia, and the School of Pharmacy of the University of Eastern Finland
• Shape Programming by Modulating Actuation over Hierarchical Length Scales by a team from the Higher School of Industrial Physics and Chemistry of the City of Paris\, the Paris Sciences and Letters University, the Sorbonne University, the International School of Advanced Studies (Italy), and the the BioRobotics Institute of the International School of Advanced Studies of the University of Sant'Anna (Italy)
• Considering Lithium-ion Battery 3D-printing via Thermoplastic Material Extrusion and Polymer Powder Bed Fusion by a team from Laboratoire de Réactivité et de Chimie des Solides, Université de Picardie Jules Verne, Laboratoire des Technologies Innovantes, Université de Picardie Jules Verne, RS2E, Réseau Français sur le Stockage Électrochimique de l’Énergie, Department of Chemistry, University of Jyväskylä, Electrical & Computer Engineering, Youngstown State University, Université Lille Nord de France, GEMTEX | Textile Research Laboratory, and Plateforme de Microscopie Électronique (PME) de l'Université de Picardie Jules Verne

• Additive Manufacturing Using Melt Extruded Thermoplastics for Tissue Engineering, part of the textbook Computer-Aided Tissue Engineering - Methods and Protocols by a team from Maastricht University's Institute for Technology-Inspired Regenerative Medicine and Aachen-Maastricht Institute for Biobased Materials
• Fused Filament Fabrication of PEEK: A Review of Process-Structure-Property Relationships by a team from The European Space Research and Technology Center
• Current and Future Applications of 3D Printing Using Custom-Made Materials Made Materials an honors thesis paper from the Chemistry Department of the University of South Dakota
• Current Understanding and Challenges in High-Temperature Additive Manufacturing of Engineering Thermoplastic Polymers by a team from the Macromolecules Innovation Institute at Virginia Tech
• Production of 3D-Printed Tympanic Membrane Scaffolds as a Tissue Engineering Application by a multi-disciplinary, multi-university team from Istanbul, Turkey
• A poly(lactic acid)-based Ink for Biodegradable Printed Electronics with Conductivity Enhanced through Solvent Aging by the Materials Science & Engineering Program of the Univeristy of Colorado, Boulder
• Advanced 3D-Printed ElectroActive Polymer (EAP) Actuator Applied to High Precision Large Optical-Quality Surface Fabrication: First Results, a presentation in Proceedings Volume 11375 of Electroactive Polymer Actuators and Devices (EAPAD) XXII
• Exploring Attacks and Defenses in Additive Manufacturing Processes: Implications in Cyber-Physical Security, a Master of Science thesis paper presented to the McKelvey School of Engineering at Washington University in St. Louis
• 3D Printing by Fused Deposition Modeling of Single- and Multi-Compartment Hollow Systems for Oral Delivery - A Review by a team from Sezione di Tecnologia e Legislazione Farmaceutiche “Maria Edvige Sangalli”, Dipartimento di Scienze Farmaceutiche, Università degli Studi di Milano
• Evaluation of Additively Manufactured Ultraperformance Polymers to use as Thermal Protection Systems for Spacecraft by a team from Centre for Additive Manufacturing, School of Engineering, Royal Melbourne Institute of Technology University and Department of Mechanical Engineering, The University of Texas at Austin
• 3D Printing of Recycled PET Polymer Composite Infused with Sustainable Carbon by a team from the Materials Science & Engineering Department of Tuskegee University

FDM/HFF, 2019

• Bioresorbable Composite Stents for Enhanced Response of Vascular Smooth Muscle Cells by H. Mozafari from The Department of Mechanical & Materials Engineering at the University of Nebraska - Lincoln
• The Impact of 3D Printing Process Parameters on the Dielectric Properties of High Permittivity Composites by a team from Loughborough University
• Additive Manufacturing of Multi-Material Systems for Aerospace Applications by a team from NASA's Glenn Research Center
• Material Extrusion-Based Additive Manufacturing of Polypropylene: A Review on How to Improve Dimensional Inaccuracy and Warpage, in the Journal of Applied Polymer Science
• Magnetic 3D Printing of Hexaferrite Material, a PhD dissertation from the University of California, Los Angeles (UCLA) Electrical and Computer Engineering Department.
• Prediction and Experimental Validation of Part Thermal Historyin Fused Filament Fabrication Additive Manufacturing Process by a team from SUNY Buffalo's Department of Mechanical and Aerospace Engineering, Department of Materials Design and Innovation, and Department of Industrial and Systems Engineering and the University of Nebraska-Lincoln Department of Mechanical and Materials Engineering
• Gastric Residence Systems for Sustained Delivery of Adamantane-class Drugs by a team from Lyndra Theraputics
• Gastric Resident Electronics a patent application by a team from the the Massachusetts Institute of Technology (MIT)
• Smart Additive Manufacturing Using Advanced Data Analytics and Closed Loop Control, A Dissertation Presented to The Academic Faculty of the Grado Department of Industrial and Systems Engineering (ISE) at Virginia Tech
• The Advent of a Novel Manufacturing Technology in Pharmaceutics: Superiority of Fused Deposition Modeling 3D Printer by a team from the College of Pharmacy and the Yonsei Institute of Pharmaceutical Sciences, Yonsei University
• On the thermal processing and mechanical properties of 3D-printed polyether ether ketone (PEEK) by a team from the Department of Macromolecular Sciences & Engineering, Case Western Reserve University School of Engineering and the Key Laboratory of E&M, Zhejiang University of Technology
• Composites based on metallic particles and tuned filling factor for 3D-printing by Fused Deposition Modeling by a team from IMDEA Nanociencia in Madrid
• 3D printing of Auxetic Metamaterials with Digitally Reprogrammable Shape by a team from the Georgia Tech School of Mechanical Engineering
• Automated Fiber Embedding for Tailoring Mechanical and Functional Properties of Soft Robot Components by the Singapore University of Technology and Design's (SUTD) DManD (Digitial Manufacturing and Design) Center
• Image Analysis-Based Closed Loop Quality Control for Additive Manufacturing with Fused Filament Fabrication by a team from the Virginia Tech Grado Department of Industrial and Systems Engineering
• Reprocessable 3D-Printed Conductive Elastomeric Composite Foams for Strain and Gas Sensing by a team from the Chemistry and Macromolecular Science & Engineering Departments of Case Western Reserve University
• Chapter 7 - Additive Manufacturing of Polyaryletherketones in the PEEK Biomaterials Handbook
• Fast Scanning Calorimetry for Semicrystalline Polymers in Fused Deposition Modeling by a team from The Materials Science and Engineering School of Georgia Tech

FDM/HFF, 2018

• Synthesis and Characterization of Novel Bioplastics by innovative 3D Printing Approaches, a Masters Thesis by Kathryn Hall from the University of North Dakota
• Mechanical Characterizations of 3D-printed PLLA/Steel Particle Composites by a team from the Department of Mechanical & Materials Engineering, University of Nebraska-Lincoln
• Precision Enhancement of 3D Printing via in-situ Metrology by a team from UCLA's Mechanical and Aerospace Engineering and Electrical and Computer Engineering Departments and the NanoSystems Institute
• Feedstock for 3D Printing and Uses Thereof Patent application by a team from The University of Southern Denmark
• Interlayer Bonding Improvement of Material Extrusion Parts with Polyphenylene Dulfide Using the Taguchi Method by a team from the Georgia Tech School of Materials Science and Engineering
• 3D Printed Sustainable Biochar-Recycled PET Composite by a team from Tuskegee University
• Monitoring Temperature in Additive Manufacturing with Physics-Based Compressive Sensing by a team from [www.me.gatech.edu The Mechanical Engineering School at Georgia Tech]
• 3D Printed Acoustic Metamaterial Sound Absorbers using Functionally-Graded Sonic Crystals by a team from the US Naval Research Laboratory
• Pharmaceutical 3D Printing: Design and Qualification of a Single Step Print and Fill Capsule by a team from Merck Pharmaceuticals
• Fabrication and Properties of Novel Polymer-Metal Composites using Fused Deposition Modeling by the Mechanical Engineering Staff at Worcester Polytechnic Institute

FDM/HFF, 2017

• NANOSATC-BR2, 2 unit CUBESAT, Power Analysis, Solar Flux Prediction, Design and 3D Printing of the Flight Model from the UFSM & INPE’S NANOSATC-BR, CUBESAT Development Program by a team from the Federal University of Santa Maria (UFSM), Brasil.
• Tensile Mechanical Properties of Polypropylene Composites Fabricated by Material Extrusion, a reviewed paper of the Solid Freeform Fabrication Symposium 2017.
• Effect of Process Parameters and Shot Peening on Mechanical Behavior of ABS Parts Manufactured by Fused Filament Fabrication (FFF), a reviewed paper of the Solid Freeform Fabrication Symposium 2017.
• Hybrid Processes in Additive Manufacturing in the Journal of Manufacturing Science and Engineering of the American Society of Mechanical Engineers
• Effects of Material Properties on Warpage in Fused Deposition Modeling Parts in The International Journal of Advanced Manufacturing Technology
• Thermal and Mechanical Properties of 3D Printed Boron Nitride – ABS Composites, in Applied Composite Materials
• Dynamical Majorana edge modes in a broad class of topological mechanical systems by The New Jersey Institute of Technology

FDM/HFF, 2016

• High Temperature Thermoplastic Additive Manufacturing Using Low-Cost, Open-Source Hardware published by NASA