Difference between revisions of "Emulsifiables"

From Hyrel3D
Jump to navigation Jump to search
Line 63: Line 63:
! rowspan="2" style="width: 15%" | Settings
! rowspan="2" style="width: 15%" | Settings
! colspan="5" | EMO, VOL, KRA, COD, VCD, KCD Heads ''and New KR2''<br> (17mm Tubes, Various Gear Ratios)
! colspan="5" | EMO, VOL, KRA, COD, VCD, KCD Heads ''and New KR2''<br> (17mm Tubes, Various Gear Ratios)
! colspan="4" | SDS, CSD, VSD, CVS Heads <br> (Various Tube Diameters, Standard Gear Ratios)
! colspan="5" | SDS, CSD, VSD, CVS and DSD Heads <br> (Various Tube Diameters, Standard Gear Ratios)
|-
|-
! style="width: 10%" | 19:1 Ratio
! style="width: 10%" | 19:1 Ratio
Line 74: Line 74:
! style="width: 10%" | 30cc
! style="width: 10%" | 30cc
! style="width: 10%" | 60cc
! style="width: 10%" | 60cc
! style="width: 10%" | DSD-30
|-  
|-  
!colspan="10"| Material
!colspan="11"| Material
|-  
|-  
! Type  
! Type  
| Custom
| Custom
| Custom
| Custom
| Custom
Line 90: Line 92:
! Color  
! Color  
| (any)  
| (any)  
| (any)
| (any)
| (any)
| (any)  
| (any)  
Line 102: Line 105:
| 1.600  
| 1.600  
| 1.600
| 1.600
| 1.600
| 1.600  
| 1.600  
| 1.600  
| 1.600  
Line 111: Line 115:
|-  
|-  
! Layer  
! Layer  
| 0.300
| 0.300  
| 0.300  
| 0.300  
| 0.300  
Line 121: Line 126:
| 0.300
| 0.300
|-  
|-  
!colspan="10"| Temp Info
!colspan="11"| Temp Info
|-  
|-  
! Print Temp  
! Print Temp  
Line 129: Line 134:
| 35
| 35
| 35
| 35
| 0
| 0
| 0
| 0
| 0
Line 135: Line 141:
|-  
|-  
! Power Factor
! Power Factor
| 100
| 100
| 100
| 100
| 100
Line 146: Line 153:
|-  
|-  
! Minimum
! Minimum
| 0
| 0
| 0
| 0
| 0
Line 162: Line 170:
| 0/100/200
| 0/100/200
| 0/100/200
| 0/100/200
| 0
| 0
| 0
| 0
| 0
Line 167: Line 176:
| 0
| 0
|-  
|-  
!colspan="10"| Overrides
!colspan="11"| Overrides
|-  
|-  
! Pulses
! Pulses
Line 178: Line 187:
| 0.580*
| 0.580*
| 0.225
| 0.225
| 0.150
| 0.150
| 0.150
|-  
|-  
Line 183: Line 193:
| 1.000  
| 1.000  
| 1.000  
| 1.000  
| 1.000
| 1.000
| 1.000
| 1.000
| 1.000
Line 191: Line 202:
| 1.000
| 1.000
|-  
|-  
|colspan="10"| '''Prime''' <br> ''Please note that Prime values will vary greatly from those shown, depending on the compressibility of your material.''
|colspan="11"| '''Prime''' <br> ''Please note that Prime values will vary greatly from those shown, depending on the compressibility of your material.''
|-  
|-  
! Steps
! Steps
Line 202: Line 213:
| 200
| 200
| 300
| 300
| 500
| 500
| 500
|-  
|-  
Line 212: Line 224:
| 10,000
| 10,000
| 10,000  
| 10,000  
| 10,000
| 10,000
| 10,000
| 10,000
| 10,000
Line 225: Line 238:
| 100
| 100
| 100
| 100
| 1000
|-  
|-  
! Before Tool Change
! Before Tool Change
| 1
| 1
| 1
| 1
| 1
Line 237: Line 252:
| 1
| 1
|-  
|-  
|colspan="10"| '''Unprime'''  <br> ''Please note that Unprime values will vary greatly from those shown, depending on the compressibility of your material.''
|colspan="11"| '''Unprime'''  <br> ''Please note that Unprime values will vary greatly from those shown, depending on the compressibility of your material.''
|-  
|-  
! Steps
! Steps
Line 248: Line 263:
| 160
| 160
| 225
| 225
| 400
| 400
| 400
|-  
|-  
Line 258: Line 274:
| 10,000  
| 10,000  
| 10,000
| 10,000
| 10,000
| 10,000  
| 10,000  
| 10,000
| 10,000
Line 271: Line 288:
| 100
| 100
| 100
| 100
| 1000
|-  
|-  
! After Tool Change
! After Tool Change
| 1
| 1
| 1
| 1
| 1
Line 283: Line 302:
| 1
| 1
|-  
|-  
!colspan="10"| Offsets
!colspan="11"| Offsets
|-  
|-  
! Clone Head
! Clone Head
Line 293: Line 312:
| Off  
| Off  
| Off  
| Off  
| Off
| Off
| Off
| Off  
| Off  
Line 299: Line 319:
| 0,000  
| 0,000  
| 0,000
| 0,000
| 0,000
| 0,000  
| 0,000  
| 0,000  
| 0,000  
Line 315: Line 336:
| 0,000  
| 0,000  
| 0,000
| 0,000
| 0,000
| 0,000  
| 0,000  
| 0,000
| 0,000
Line 324: Line 346:
| 0,000  
| 0,000  
| 0,000
| 0,000
| 0,000
| 0,000  
| 0,000  
| 0,000
| 0,000
Line 329: Line 352:
| 0,000
| 0,000
|-  
|-  
!colspan="10"| Head Info
!colspan="11"| Head Info
|-  
|-  
! Model
! Model
Line 335: Line 358:
| (varies)
| (varies)
| (varies)
| (varies)
| (varies)
| (varies)  
| (varies)  
| (varies)  
| (varies)  
Line 343: Line 367:
|-  
|-  
! RTD Type
! RTD Type
| 1k PLAT_RTD
| 1k PLAT_RTD
| 1k PLAT_RTD
| 1k PLAT_RTD
| 1k PLAT_RTD
Line 354: Line 379:
|-  
|-  
! Motor Current
! Motor Current
| High
| High
| High
| High
| High
Line 365: Line 391:
|-  
|-  
! Step Mode
! Step Mode
| Sixteenth
| Sixteenth
| Sixteenth
| Sixteenth
| Sixteenth
Line 375: Line 402:
| Sixteenth
| Sixteenth
|-
|-
|colspan="11"| ''* Thanks to Yasmine at VT for the precise calculation.''
|colspan="12"| ''* Thanks to Yasmine at VT for the precise calculation.''
|-  
|-  


|}
|}

Revision as of 18:36, 13 September 2016

Overview

EMO-Type heads are for printing as follows:

  • With pastes, gels, emulsifiables or waxes.
  • At room or elevated temperatures.
  • With or without UV Crosslining.
  • With Hyrel Nozzles (1.5mm, 2mm) or Luer Tips.

These include the following:

EMO-Type Head Comparison
Temperature Ambient Up to 75°C Up to 100°C Up to 150°C
No Crosslinking EMO-25

SDS-5, -10, -30, -60

VSD-5, -10, -30, -60 VOL-25 KRA-15
With Crosslinking COD-25

CSD-5, -10, -30, -60

VCS-5, -10, -30, -60 VCD-25 KCD-15

So, what do these goofy designations actually stand for?

EMO: Emulsifiables at Room Temperature
COD: Emulsifiables T Room Temperature with Crosslink On Demand
VOL: Volcano: Heated (up to 100°C) Emulsifiables
VCD: Volcanic Crosslink on Demand
KRA: Krakatoa: Heated (up to 150°C) Emulsifiables
KCD: Krakatoic Crosslink on Demand
KR2: Krakatoa v2: a more robust KRA head with a double gasketed plunger hotter, more viscous Emulsifiables
SDS: Syringe Dispensing System (uses disposable plastic syringes at room temperature)
CSD: Crosslinking Syringe Dispensing System
VSD: Volcanic Syringe Dispensing System
CVS: Crosslinking Volcanic Syringe Dispensing System

As of Sep 2016, the latest firmware is 32V, included with Repetrel 2.828.

Settings

Some settings for the EMO-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (1.6mm is default) AND what path width you sliced for. Temperature commands will be ignored by heads with no temperature control. Having said that, here are our default shipping settings:

EMO-Type Head Comparison
Settings EMO, VOL, KRA, COD, VCD, KCD Heads and New KR2
(17mm Tubes, Various Gear Ratios)
SDS, CSD, VSD, CVS and DSD Heads
(Various Tube Diameters, Standard Gear Ratios)
19:1 Ratio 27:1 Ratio 51:1 Ratio 100:1 Ratio 100:1 KR2 5cc 10cc 30cc 60cc DSD-30
Material
Type Custom Custom Custom Custom Custom Custom Custom Custom Custom Custom
Color (any) (any) (any) (any) (any) (any) (any) (any) (any) (any)
Nozzle 1.600 1.600 1.600 1.600 1.600 1.600 1.600 1.600 1.600 1.600
Layer 0.300 0.300 0.300 0.300 0.300 0.300 0.300 0.300 0.300 0.300
Temp Info
Print Temp 35 35 35 35 35 0 0 0 0 0
Power Factor 100 100 100 100 100 100 100 100 100 100
Minimum 0 0 0 0 0 0 0 0 0 0
Maximum 0/100/200 0/100/200 0/100/200 0/100/200 0/100/200 0 0 0 0 0
Overrides
Pulses 1.600 2.300 4.700 8.500 14.750 0.750 0.580* 0.225 0.150 0.150
Feed Rate % 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000
Prime
Please note that Prime values will vary greatly from those shown, depending on the compressibility of your material.
Steps 600 700 1000 4000 6000 200 200 300 500 500
Rate 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000
Dwell Time (ms) 100 100 110 120 200 100 100 100 100 1000
Before Tool Change 1 1 1 1 1 1 1 1 1 1
Unprime
Please note that Unprime values will vary greatly from those shown, depending on the compressibility of your material.
Steps 500 550 800 3500 5000 160 160 225 400 400
Rate 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000
Dwell Time (ms) 100 100 100 110 200 100 100 100 100 1000
After Tool Change 1 1 1 1 1 1 1 1 1 1
Offsets
Clone Head Off Off Off Off Off Off Off Off Off Off
X 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000
Y 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000
Z 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000
Head Info
Model (varies) (varies) (varies) (varies) (varies) (varies) (varies) (varies) (varies) (varies)
RTD Type 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD
Motor Current High High High High High High High High High High
Step Mode Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth
* Thanks to Yasmine at VT for the precise calculation.