Main Page

With literally thousands of materials to print on the Hyrel Printer, we have broken down the list of materials into logical groups based on their printing temperature and type of head used to print them.

If you are planning on using the heads which photoinitiate crosslinking, make sure you specify the correct wavelength of LED for your material.

A standard material printing data sheet has been created for materials that have been internally tested; you can access this data by clicking on the material name below.

Printers

As of Jan, 2016, Hyrel Printers are available in two models: Engines and Systems.

Engines and Systems

Engines are open-air models. Detailed information is on the Engines page. Systems are enclosed models. Detailed information is on the Systems page. Both models feature over 200x200x200mm of build volume. Each model can take up to four of our modular heads detailed below. Build plates will get to between 70°C and 85°C, depending on ambient temperature.

The Next Big Thing

Information not yet available. :)

Cold Flow

Cold Flow means fluid (non-filament-based) materials which are deposited at room temperature, with or without UV Crosslinking.

Materials, Cold Flow

• 3P Quick Cure Clay
• Adhesives
• Clay
• Epoxy, Two-part
• Fimo
• Glue
• Kato
• Metal Clay, including Precious Metal Clay (PMC)
• Modeling Clay
• PEG
• Porcelain
• Plasticine
• Play-Doh
• Resins
• RTV Silicone
• Sculpey
• Sugru

Heads, Cold Flow

Cold Flow Head Properties

Head	Container	Capacity	Nozzle	UV Crosslinking
EMO-25	Aluminum	25cc	1.5mm, 2.0mm, Luer	No
COD-25	Aluminum	25cc	Luer	Yes
SDS-5	Syringe	05cc	Luer	No
CSD-5	Syringe	05cc	Luer	Yes
SDS-10	Syringe	10cc	Luer	No
CSD-10	Syringe	10cc	Luer	Yes
SDS-30	Syringe	30cc	Luer	No
CSD-30	Syringe	30cc	Luer	Yes
SDS-60	Syringe	60cc	Luer	No
CSD-60	Syringe	60cc	Luer	Yes

Research Papers Citing Hyrel Cold Flow

• Bioactive Nanoengineered Hydrogels for Bone Tissue Engineering: A Growth-Factor-Free Approach in The American Chemical Society's ACS Nano
• Design and Fabrication of 3D Printed Scaffolds with a Mechanical Strength Comparable to Cortical Bone to Repair Large Bone Defects in Nature.com's Scientific Reports

Warm Flow

Warm Flow means fluid (non-filament-based) materials which are deposited at up to 100°C, with or without UV Crosslinking.

PCL and other medium temperature material can be printed directly from Pellets the size of small peas. If you pulverize or powder your polymer, it is possible to pre-mix the material dry and test different alloys of plastics.

Materials, Warm Flow

• Adhesives
• Fimo
• Kato
• Glue
• Plasticine
• Resins
• Sculpey
• Wax

Note that some materials (like Fimo, Plasticine and Sculpey) flow more freely when slightly above room temperature, and perhaps too freely at higher temperatures.

Heads, Warm Flow

Cold Flow Head Properties

Head	Max Temp	Container	Capacity	Nozzle	UV Crosslinking
VOL-25	100°C	Aluminum	25cc	1.5mm, 2.0mm, Luer	No
VCD-25	100°C	Aluminum	25cc	Luer	Yes
KRA-15	150°C	Stainless	15cc	1.5mm, 2mm, Luer	No
KCD-15	150°C	Stainless	15cc	Luer	Yes

Hot Flow

Hot Flow means 1.75mm diameter, filament-based materials which are deposited at up to 250°C, with

Materials, Hot Flow

• ABS
• BendLay
• FilaFlex
• Flex45
• LayBrick
• LayWood
• NinjaFlex
• Nylon
• PC
• PEEK
• PET
• PETG
• PETT
• PLA
• PlastInk Rubber
• PP
• PVA
• T-Glase

Heads, Hot Flow

Cold Flow Head Properties

Head	Min Temp	Max Temp	Filament Type	Nozzle	Recommended For
MK1-250	150°C	250°C	Standard	.35mm, .50mm, .75mm, 1.0mm	ABS, LayBrick, LayWood, Nylon PC, PET, PETG, PETT, PLA, PP, PVA, T-Glase
MK2-250	150°C	250°C	Flexible	.35mm, .50mm, .75mm, 1.0mm	BendLay, FilaFlex, Flex45, NinjaFlex, PlastInk Rubber
MK1-450	250°C	450°C	Engineering	.50mm	PC, PEEK

Research Papers Citing Hyrel Hot Flow

• Demonstration and Characterization of Fully 3D-printed RF Structures, The Institute of Electrical and Electronics Engineers, Incorporated (IEEE)
• Infill Dependent 3D-Printed Material Based on NinjaFlex Filament for Antenna Applications, The Institute of Electrical and Electronics Engineers, Incorporated (IEEE)
• A Novel Strain Sensor Based on 3D Printing Technology and 3D Antenna Design, The Institute of Electrical and Electronics Engineers, Incorporated (IEEE)
• A Novel 3-D Printed Loop Antenna Using Flexible NinjaFlex Material for Wearable and IoT Applications, The Institute of Electrical and Electronics Engineers, Incorporated (IEEE)
• RF Characterization of 3D Printed Flexible Materials - NinjaFlex Filaments, The European Microwave Association (EuMA)