Reservoir Heads OLD

From Hyrel3D
Revision as of 16:28, 15 July 2020 by Davo (talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

This page has settings for older version reservoir heads, in case users wish to remain on older software.

Settings for Reservoir Heads

Non-Hydra units shipping through spring 2017 ship with Repetrel version 2.x. Hydra units, and other units shipping as of summer 2017 will have version 3.x, and should consult the version 3.x tables, below. All units should be upgraded to 3.x when it is available. If you run a head with v2 settings on a v3 install, the background will flash red; please make the changes below:

Values for versions 1.x and 2.x will be inicated in RED.
Values for version 3.x will be inicated in BLUE.
Values for version 4.x will be inicated in GREEN.
Please note that for v4, you can load settings from file.

Note that you must flash these settings to the head to make them the new default.

Some settings for the EMO-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (1.6mm is default) AND what path width you sliced for. Temperature commands will be ignored by heads with no temperature control. Having said that, below are our default shipping settings:

METAL Reservoir Heads

Settings for Reservoir Heads with METAL Reservoirs
Settings EMO, VOL, KRA (old), KR2 and TAM (17mm Tubes, Various Gear Ratios)
19:1 Ratio 27:1 Ratio 51:1 Ratio 100:1 KRA (old) 100:1 EMO-XT,
KR2, TAM 		100:1 EMO-ST,
KR2-ST, TAM-ST
Material
Type Custom Custom Custom Custom Custom Custom
Color (any) (any) (any) (any) (any) (any)
Nozzle 1.600 1.600 1.600 1.600 1.600 1.600
Layer 0.300 0.300 0.300 0.300 0.300 0.300
Temp Info
Print Temp 35 35 35 35 35 35
Power Factor 100 100 100 100 100 100
Minimum 0 0 0 0 0 0
Maximum 0 0/80 0/80 0/80/150 0/80/150/250 0/80/150/250
Overrides
Pulses / µL 1.6 / 176 / 176 2.3 / 275 / 275 4.8 / 517 / 517 9.0 / 1,000 / 1,000 15 / 600 / 1200 ? / ? / ?
Multiplier 1 1 1 1 1 / 2 / 1 1 / 2 / 1
Prime
Steps 7000 6000 1000 3000 6000 ?
Rate 10,000 10,000 10,000 10,000 10,000 ?
Dwell Time (ms) 700 600 100 300 600 ?
Before Tool Change 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a n/a
Unprime
Steps 7000 6000 1000 3000 6000 ?
Rate 10,000 10,000 10,000 10,000 10,000 ?
Dwell Time 600 / -700 / -700 500 / -600 / -600 100 / -100 / -100 300 / -300 / -300 500 / -600 / -600 n/a
After Tool Change 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a n/a
Offsets
Clone Head Off Off Off Off Off Off
X 0,000 0,000 0,000 0,000 0,000 0,000
Y 0,000 0,000 0,000 0,000 0,000 0,000
Z 0,000 0,000 0,000 0,000 0,000 0,000
Head Info
Model (varies) (varies) (varies) (varies) (varies) (varies)
PCB Type n/a / n/a / 4988/160J n/a / n/a / 4988/160J n/a / n/a / 4988/160J n/a / n/a / 4988/160J n/a / n/a / 4988/160J 4988/160J
RTD Type 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD
Motor Current High / High / n/a High / High / n/a High / High / n/a High / High / n/a High / High / n/a n/a
Step Mode 16th / 16th / n/a 16th / 16th / n/a 16th / 16th / n/a 16th / 16th / n/a 16th / 16th / n/a n/a
Plot Settings (any) (any) (any) (any) (any) (any)
Motor Settings
Step Mode n/a / n/a / 16th n/a / n/a / 16th n/a / n/a / 16th n/a / n/a / 16th n/a / n/a / 16th ?
Motor Current n/a / n/a / Normal n/a / n/a / Normal n/a / n/a / Normal n/a / n/a / Normal n/a / n/a / Normal ?
Max Jog Rate n/a / n/a / 5,000 n/a / n/a / 5,000 n/a / n/a / 10,000 n/a / n/a / 15,000 n/a / n/a / 15,000 ?
Rot Speed n/a / n/a / 7,500 n/a / n/a / 1,500 n/a / n/a / 1,500 n/a / n/a / 15,000 n/a / n/a / 15,000 ?
Settings 19:1 Ratio 27:1 Ratio 51:1 Ratio 100:1 KRA (old) 100:1 EMO-XT,
KR2, TAM 		100:1 EMO-ST,
KR2-ST, TAM-ST
EMO, VOL, KRA (old), KR2 and TAM (17mm Tubes, Various Gear Ratios)

PLASTIC Reservoir Heads

Settings for Reservoir Heads with PLASTIC Reservoirs
Settings SDS, HSD, and RSD Heads (with or without COD)
(Various Tube Diameters, Standard Gear Ratios) 		DSD-50 (1:1) Special (with or without COD)
1cc ET 5cc 10cc 30cc 60cc 150cc XT DSD-50 HSD-10-Ardes SDS-30XT SDS-60XT
Material
Type Custom Custom Custom Custom Custom Custom Custom Custom Custom Custom
Color (any) (any) (any) (any) (any) (any) (any) (any) (any) (any)
Nozzle 1.600 1.600 1.600 1.600 1.600 4.00 1.600 1.600 1.600 1.6000
Layer 0.300 0.300 0.300 0.300 0.300 0.300 0.300 0.300 0.300 0.300
Temp Info
Print Temp 0 0 0 0 0 0 0 35 0 0
Power Factor 100 100 100 100 100 100 100 100 100 100
Minimum 0 0 0 0 0 0 0 0 0 0
Maximum 0 0 0 0; 75 for HSD 0 0 0 130 0 0
Overrides
Pulses / µL 5.8 / 610 / 610 0.75 / 81 / 81 0.58 / 62.5 / 62.5 0.225 / 30 / 30 0.15 / 19.4 / 19.4 12.8 / 12.8 / 12.8 0.135 / 20 / 20 ? / 900 / 900 ? / 86 / 86 ? / 25 / 28.8
Multiplier 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1 / 2 / 2 1.000 1.000
Prime
Steps 7500 1500 3000 2250 1500 1500 1 9000 1125 1500
Rate 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000
Dwell Time (ms) 800 150 300 300 300 300 100 900 300 300
Before Tool Change 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a
Unprime
Steps 7500 1500 3000 2250 1500 1500 1 9000 1125 1500
Rate 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000
Dwell Time 800 / -800 / -800 300 / -300 / -300 300 / -300 / -300 300 / -300 / -300 300 / -300 / -300 300 / -300 / -300 1 / -1 / -1 900 / -900 / -900 300 / -300 / -300 300 / -300 / -300
After Tool Change 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a 2 / n/a / n/a
Offsets
Clone Head Off Off Off Off Off Off Off Off Off Off
X 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000
Y 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000
Z 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000
Head Info
Model (varies) (varies) (varies) (varies) (varies) (varies) (varies) (varies) (varies) (varies)
PCB Type n/a / n/a / 4988/160J n/a / n/a / 4988/160J n/a / n/a / 4988/160J n/a / n/a / 4988/160J n/a / n/a / 4988/160J n/a / n/a / 4988/160J n/a / n/a / 4988/160J n/a / n/a / 4988/160J n/a / n/a / 4988/160J n/a / n/a / 4988/160J
RTD Type None None None None; varies
for HSD, RSD 		None None None 1k_PLAT_RTD None None
Motor Current High / High / n/a High / High / n/a High / High / n/a High / High / n/a High / High / n/a High / High / n/a High / High / n/a High / High / n/a High / High / n/a High / High / n/a
Step Mode 16th / 16th / n/a 16th / 16th / n/a 16th / 16th / n/a 16th / 16th / n/a 16th / 16th / n/a 16th / 16th / n/a 16th / 16th / n/a 16th / 16th / n/a 16th / 16th / n/a 16th / 16th / n/a
Plot Settings (any) (any) (any) (any) (any) (any) (any) (any) (any) (any)
Motor Settings
Step Mode n/a / n/a / 16th n/a / n/a / 16th n/a / n/a / 16th n/a / n/a / 16th n/a / n/a / 16th n/a / n/a / 16th n/a / n/a / 16th n/a / n/a / 16th n/a / n/a / 16th n/a / n/a / 16th
Motor Current n/a / n/a / Normal n/a / n/a / Normal n/a / n/a / Normal n/a / n/a / Normal n/a / n/a / Normal n/a / n/a / Normal n/a / n/a / Normal n/a / n/a / Normal n/a / n/a / Normal n/a / n/a / Normal
Max Jog Rate n/a / n/a / 10,000 n/a / n/a / 10,000 n/a / n/a / 10,000 n/a / n/a / 10,000 n/a / n/a / 10,000 n/a / n/a / 10,000 n/a / n/a / 10,000 n/a / n/a / 10,000 n/a / n/a / 10,000 n/a / n/a / 10,000
Rot Speed n/a / n/a / 1,500 n/a / n/a / 1,500 n/a / n/a / 1,500 n/a / n/a / 1,500 n/a / n/a / 1,500 n/a / n/a / 1,500 n/a / n/a / 1,500 n/a / n/a / 7,500 n/a / n/a / 1,500 n/a / n/a / 1,500
Settings 1cc ET 5cc 10cc 30cc 60cc 150cc XT DSD-50 HSD-10-Ardes SDS-30XT SDS-60XT
SDS, HSD, and RSD Heads (with or without COD)
(Various Tube Diameters, Standard Gear Ratios) 		DSD-50 (1:1) Special (with or without COD)
Retrieved from "https://hyrel3d.in/wiki/index.php?title=Reservoir_Heads_OLD&oldid=4961"