Test
Jump to navigation
Jump to search
Chart of Codes
| Code | Supported | Brief Description |
|---|---|---|
| G0 | Yes | Rapid Move |
| G1 | Yes | Working Move |
| G2 | Yes | Clockwise Arc |
| G2.1 | Yes | Spiral CW Arc1 |
| G2.2 | Yes | Spiral CW Arc2 |
| G2.3 | Yes | 3-Space CW Spiral Arc |
| G3 | Yes | Counterclockwise Arc |
| [[#G3.1_Spiral_CCW_Arc1|G3.1]] | Yes | Spiral CCW Arc1 |
| G3.2 | Yes | Spiral CCW Arc2 |
| G3.3 | Yes | 3-Space CCW Spiral Arc |
| G4 | Yes | Timed Pause |
| G10 | No | Absolute E |
| G11 | No | Relative E |
| G16 | Yes | Arc in Any Plane |
| G17 | Yes | Arc in XY Plane |
| G18 | Yes | Arc in XZ Plane |
| G19 | Yes | Arc in YZ Plane |
| G20 | Yes | Set Units to Inches |
| G21 | Yes | Set Units to Milimeters |
| G28 | Yes | Send X, Y to Physical Home |
| G53 | Yes | Clear Offsets |
| G54-59 | Yes | Set Offsets |
| G81 | G81 | Peck Drilling |
| G90 | Yes | Absolute Positioning |
| G91 | Yes | Relatative Positioning |
| G92 | Yes | Reset Coordinates |
| G93 | Yes | Reset Coordinates |
| M0 | Yes | Stop Until Resume |
| M3 | Yes | Spindle On CW |
| M4 | Yes | Spindle On CCW |
| M5 | Yes | Spindle Off |
| M6 | Yes | Declare Head Offsets |
| M7 | Yes | Aux 1 On (Mist) |
| M8 | Yes | Aux 2 On (Flood) |
| M9 | Yes | All Aux Off |
| M17 | Yes | Engage Motors |
| M18 | Yes | Disengage Motors |
| M30 | Yes | End of Program |
| M82 | Yes | Absolute E-Values |
| M83 | Yes | Relative E-Values |
| M84 | Yes | Disable Motors |
| M104 | Yes | Set Temp (Head) |
| M106 | Yes | Set Cooling / Etc. |
| M107 | Yes | Stop Cooling / Etc. |
| M109 | Yes | Wait for Temp (Head) |
| M116 | No | Pause for All Temps |
| M140 | Yes | Set Temp (Bed) |
| M141 | Yes | Set Temp (Chamber) |
| M190 | Yes | Wait for Temp (Bed) |
| M191 | Yes | Wait for Temp (Chamber) |
| M203 | Yes | Set G0 Speed |
| M221 | Yes | Set Flow Rate |
| M229 | Yes | Use E Values |
| M253 | Yes | Turn On Lathe (CW) |
| M254 | Yes | Turn On Lathe (CCW) |
| M255 | Yes | Turn Off Lathe |
| M619 | Yes | Map Aux Port |
| M620 | Yes | Enable Device |
| M621 | Yes | Set Laser Power |
| M623 | Yes | Duration Emit |
| M660 | Yes | Set Tool Offsets |
| M670 | Yes | Enable Y-arm Light |
| M671 | Yes | Activate Danger Light |
| M672 | Yes | Set Y-arm Light |
| M675 | Yes | Activate Response LEDs |
| M676 | Yes | Activate Recirc. Fan |
| M677 | Yes | Activate Buzzer |
| M678 | Yes | Activate Laser X-hair |
| M679 | Yes | Activate Vacuum |
| M684 | Yes | Activate Exhaust |
| M685 | Yes | Activate Air |
| M689 | Yes | Activate Ext. Head |
| M701 | Yes | Set Head Reporting |
| M702 | Yes | Establish Clone Squad |
| M703 | Yes | Add to Clone Squad |
| M704 | Yes | Remove from Clone Squad |
| M718 | Yes | Stop Logging to File |
| M719 | Yes | Start Logging to File |
| M721 | Yes | Set Unprime Values |
| M722 | Yes | Set Prime Values |
| M723 | Yes | Set Manual Flow |
| M728 | Yes | Set Motor Current Boost |
| M756 | Yes | Set Height for Flow |
| M772 | Yes | Reset All Metrics |
| M773 | Yes | Generate Basic Report |
| M783 | Yes | Tie Aux to Extrusion |
| M790 | Yes | New Layer Actions |
| M791 | Yes | Snap Image |
| M792 | Yes | Execute Action |