Sekret!
Using the T with the ESR and 30M
| Yoke Image |
| ||||
|---|---|---|---|---|---|
| Description | 1st Slot | No Slot | 2nd Slot | 3rd Slot | 4th Slot |
| T Command | T0 | N/A | T1 | T2 | T3 |
| T Variable | T11 | N/A | T12 | T13 | T14 |
| Global Variable | T10 | ||||
| Resistor Value | 2,200 | N/A | 3,300 | 4,700 | 6,800 |
Using the T with the EHR and 16A (Single Yoke)
| Yoke Image |
| ||||
|---|---|---|---|---|---|
| Description | 1st Slot | 2nd Slot | 3rd Slot | 4th Slot | 5th Slot |
| T Command | T0 | T1 | T2 | T3 | T4 |
| T Variable | T11 | T12 | T13 | T14 | T15 |
| Global Variable | T10 | ||||
| Resistor Value | 2,200 | 3,300 | 4,700 | 6,800 | 10,000 |
Using the T with the 16A (Dual Yoke)
| Yoke Image |
|
| ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Description | 2nd Yoke, 1st Slot |
2nd Yoke, 2nd Slot |
2nd Yoke, 3rd Slot |
2nd Yoke, 4th Slot |
2nd Yoke, 5th Slot |
1st Yoke, 1st Slot |
1st Yoke, 2nd Slot |
1st Yoke, 3rd Slot |
1st Yoke, 4th Slot |
1st Yoke, 5th Slot |
| T Command | T5 | T6 | T7 | T8 | T9 | T0 | T1 | T2 | T3 | T4 |
| T Variable |
T21 | T22 | T23 | T24 | T25 | T11 | T12 | T13 | T14 | T15 |
| Global Variable | T20 | T10 | ||||||||
| Resistor Value | 1,500 | 2,700 | 3,900 | 5,600 | 8,200 | 2,200 | 3,300 | 4,700 | 6,800 | 10,000 |
Special Addresses
| Description | T Command | T Variable | Position Ω |
|---|---|---|---|
| All Devices | n/a | M# T0 | n/a |
| All Heads | n/a | M# T100 | n/a |
| Yoke 1, All Slots | n/a | M# T10 | n/a |
| Yoke 2, All Slots | n/a | M# T20 | n/a |
| Aux Port | T10 | n/a | ? |
| CO2 Laser | T11 | M# T41 | 22,000 |
| 3-Phase Spindle | T12 | M# T26 | 560 |
| Primary Bed/Chamber | n/a (T13) | M# T91 | 0 |
| Secondary Bed/Chamber | n/a (T14) | M# T92 | 12,000 |
| All Beds/Chambers | n/a | M# T90 | n/a |
Gcodes the customer shouldn't need
M670 Toggle Y-Arm Light Now
Turn on Y-arm light immediately.
M671 Toggle X-Arm Lights
Toggle X-arm Lights
M672 Toggle Y-Arm with Sensor
See main Gcode page.
M673 Toggle Y-Arm Light Next
Toggle Y-arm light after all previous commands are finished.
M797 Report Sensors
Generates a text report of sensor states in 3D-View text window!
M797 I1 reports what is homed and what is not:
>GB: AX ST DR HM L1 L2 FT >GB: == == == == == == == >GB: X 1 1 1 0 0 1 >GB: Y 1 1 0 0 0 1 >GB: Z 1 0 1 0 0 1 >GB: A 0 0 1 0 0 1 >GB: B 0 0 0 0 0 0 >GB: C 0 0 0 0 0 0
AX - Axis ST - Step DR - Direction HM - Home L1 - Limit 1 L2 - Limit 2 FT - Fault