Difference between revisions of "Settings"

From Hyrel3D
Jump to navigation Jump to search
 
(9 intermediate revisions by the same user not shown)
Line 10: Line 10:


# Go to Setings > Printer.
# Go to Setings > Printer.
# Click "Load Settings from File" (find your custom file, or the most recent one named for your model of printer)
# Click "Load Settings from File" - see file names below
# Make any customization you like
# Make any customization you like
# Click "Flash Motion Settings"
# Click "Flash Motion Settings"
Line 16: Line 16:
# Click "Save Settings To File" with your custom name, as a backup
# Click "Save Settings To File" with your custom name, as a backup
# Click "OK"
# Click "OK"
These steps are performed in this video: https://www.youtube.com/watch?v=N1HZOvWKqs8


Note that after flashing, or upon startup, you will be required to home the X and Y axes before other moves are allowed; on the EHR, you will also have to home the Z. This is so that the printer knows where you are and whether or not it is safe to move the amount you tell it to. If you unlock your motors or press the emergency stop button, you should home the X and Y axes again before making other movements (also Z on EHR).
Note that after flashing, or upon startup, you will be required to home the X and Y axes before other moves are allowed; on the EHR, you will also have to home the Z. This is so that the printer knows where you are and whether or not it is safe to move the amount you tell it to. If you unlock your motors or press the emergency stop button, you should home the X and Y axes again before making other movements (also Z on EHR).
Line 21: Line 23:
While each printer is shipped with tested, verified settings, you are welcome to customize your unit. For example, a second yoke will reduce your max travel in the X; an auxiliary build plate may have smaller dimensions; tall Hydras will have more travel in the Z; and you will probably want to limit your travel if you've added a vise or chuck.
While each printer is shipped with tested, verified settings, you are welcome to customize your unit. For example, a second yoke will reduce your max travel in the X; an auxiliary build plate may have smaller dimensions; tall Hydras will have more travel in the Z; and you will probably want to limit your travel if you've added a vise or chuck.


'''The latest Printer Settings files are available at [http://hyrel3d.net/downloads/repetrel/Printer_Settings_2019.10.08.rar http://hyrel3d.net/downloads/repetrel/Printer_Settings_2019.10.08.rar]''' Note that these are included in the latest v4 Repetrel download.
'''The latest Printer Settings files are available at [http://hyrel3d.net/downloads/repetrel/Printer_Settings_2019.12.05.rar http://hyrel3d.net/downloads/repetrel/Printer_Settings_2019.12.05.rar]''' Note that these are included in the latest v4 Repetrel download.
 
=== '''File Names''' ===
 
When you select "Load settings from File" (or "Switch Printer Type" from the menu), here's what the file names mean:
 
{| border="1" class="wikitable" style="width: 50%;"
|+ Printer Files
! style="width: 20%;" | File Name
! style="width: 20%;" | Model/Version
! style="width: 20%;" | Special Notes
|-
| 16AS
| 16A Standard
| Standard
|-
| 16AS_2Y
| 16A Standard
| 2nd Yoke
|-
| 16AS_2Y_45A
| 16A Standard
| 2nd Yoke, 4th/5th Axis
|-
| 16AS_45A
| 16A Standard
| 4th/5th Axis
|-
| 16AT
| 16A Tall
| Standard
|-
| 16AT_2Y
| 16A Tall
| 2nd Yoke
|-
| 16AT_2Y_45A
| 16A Tall
| 2nd Yoke, 4th/5th Axis
|-
| 16AT_45A
| 16A Tall
| 4th/5th Axis
|-
| 30M_ESR
| 30M and ESR
| Standard
|-
| EHR_diffXY
| EHR
| *early models
|-
| EHR_standard
| EHR
| Standard
|-
| ESR_30M
| ESR, 30M
| Standard
|-
| 30M_ESR
| 30M, ESR
| (same as above)
|-
| fadal429
| Fadal CNC
| Standard
|-
|}


== '''Ecosystem Apps''' ==
== '''Programs''' ==


In Repetrel, go to the Programs tab, and double click in each text field, pointing the applications to their respective executable files under <code>C:/EcosystemApps</code>. See the table below for the proper locations. Note the new location for the Slic3r install; Slic3r Recipes (or Slic3r CFG files) should still be under <code>C:\Users\Hyrel\AppData\Roaming\Slic3r</code>.
In Repetrel, go to the Programs tab, and double click in each text field, pointing the applications to their respective executable files under <code>C:/EcosystemApps</code>. See the table below for the proper locations. Note the new location for the Slic3r install; Slic3r Recipes (or Slic3r CFG files) should still be under <code>C:\Users\Hyrel\AppData\Roaming\Slic3r</code>.
Line 65: Line 135:
Note that if your login ID is not "Hyrel", you'll need to adjust the location for the Slic3r cfg file appropriately. Remember to click APPLY when done to cause these settings to be applied.
Note that if your login ID is not "Hyrel", you'll need to adjust the location for the Slic3r cfg file appropriately. Remember to click APPLY when done to cause these settings to be applied.


== '''Head Settings''' ==
== '''Head & Bed Settings''' ==


'''The latest Head Settings files are available at [http://hyrel3d.net/downloads/repetrel/Head_Settings_2019.10.08.rar http://hyrel3d.net/downloads/repetrel/Head_Settings_2019.10.08.rar]''' Note that these are included in the latest v4 Repetrel download.
'''The latest Head Settings files are available at [http://hyrel3d.net/downloads/repetrel/v4_Head_Settings.rar http://hyrel3d.net/downloads/repetrel/Head_Settings_2019.12.05.rar]''' Note that these are included in the latest v4 Repetrel download.


For Filament-based heads, see the table(s) on our [[Hot_Flow]] page.
For Filament-based heads, see the table(s) on our [[Hot_Flow]] page.


For Reservoir-based heads, see the table(s) on our [[Cold_and_Warm_Flow]] page.
For Reservoir-based heads, see the table(s) on our [[Cold_and_Warm_Flow]] page.
For Hotbeds, we now (v4) have files stored, just like head settings files. If you didn't get them, email me and I'll put the info here.
The names should be self-explanatory:
* bed_30M_ESR.txt
* bed_120_hydra.txt
* bed_200_hydra.txt
* bed_EHR.txt
Right-click on the head (anywhere EXCEPT the "FLASH" button) and open the proper file for your head or bed:
[[File:Loadfromfile1.png|250px]]
And select the file for the device for which you wish to load the settings:
[[File:Loadfromfile2.png|500px]]
Please note that on some versions, the RTD type is, unfortunately, not populated. For heads, check the pages above.
ESR and 30M units should use "'''10K'''".
EHR and 16A units should use "'''1k PRTD'''"
As with all settings, to store them as defaults, go to the last page and right-click FLASH:
[[File:Rcflash1.png|500px]]
And then click YES:
[[File:Rcflash2.png|250px]]


== '''Slicer Settings''' ==
== '''Slicer Settings''' ==


For Slicer settings, see the [[Recipes]] page.
For Slicer settings, see the [[Recipes]] page.

Latest revision as of 13:56, 5 April 2021

Printer Settings

Last, you should (re)load your settings; there are several screens, detailed below.

To load a configuration file, do the following:

  1. Go to Setings > Printer.
  2. Click "Load Settings from File" - see file names below
  3. Make any customization you like
  4. Click "Flash Motion Settings"
  5. Click "Apply"
  6. Click "Save Settings To File" with your custom name, as a backup
  7. Click "OK"

These steps are performed in this video: https://www.youtube.com/watch?v=N1HZOvWKqs8

Note that after flashing, or upon startup, you will be required to home the X and Y axes before other moves are allowed; on the EHR, you will also have to home the Z. This is so that the printer knows where you are and whether or not it is safe to move the amount you tell it to. If you unlock your motors or press the emergency stop button, you should home the X and Y axes again before making other movements (also Z on EHR).

While each printer is shipped with tested, verified settings, you are welcome to customize your unit. For example, a second yoke will reduce your max travel in the X; an auxiliary build plate may have smaller dimensions; tall Hydras will have more travel in the Z; and you will probably want to limit your travel if you've added a vise or chuck.

The latest Printer Settings files are available at http://hyrel3d.net/downloads/repetrel/Printer_Settings_2019.12.05.rar Note that these are included in the latest v4 Repetrel download.

File Names

When you select "Load settings from File" (or "Switch Printer Type" from the menu), here's what the file names mean:

Printer Files
File Name Model/Version Special Notes
16AS 16A Standard Standard
16AS_2Y 16A Standard 2nd Yoke
16AS_2Y_45A 16A Standard 2nd Yoke, 4th/5th Axis
16AS_45A 16A Standard 4th/5th Axis
16AT 16A Tall Standard
16AT_2Y 16A Tall 2nd Yoke
16AT_2Y_45A 16A Tall 2nd Yoke, 4th/5th Axis
16AT_45A 16A Tall 4th/5th Axis
30M_ESR 30M and ESR Standard
EHR_diffXY EHR *early models
EHR_standard EHR Standard
ESR_30M ESR, 30M Standard
30M_ESR 30M, ESR (same as above)
fadal429 Fadal CNC Standard

Programs

In Repetrel, go to the Programs tab, and double click in each text field, pointing the applications to their respective executable files under C:/EcosystemApps. See the table below for the proper locations. Note the new location for the Slic3r install; Slic3r Recipes (or Slic3r CFG files) should still be under C:\Users\Hyrel\AppData\Roaming\Slic3r.

EcosystemApps Locations
Program Name Executable Location
Slic3r EXE C:\EcosystemApps\Slic3r\slic3r.exe
Slic3r CFG C:\Users\Hyrel\AppData\Roaming\Slic3r
OpenSCAD C:\EcosystemApps\OpenSCAD\openscad.exe
FreeCAD C:\EcosystemApps\FreeCAD 0.15\bin\FreeCAD.exe
MeshLab C:\EcosystemApps\VCG\MeshLab\meshlab_32.exe
FlatCAM C:\EcosystemApps\FlatCAM\FlatCAM.exe
QCAD C:\EcosystemApps\QCAD\qcad.exe
TeamViewer C:\EcosystemApps\TeamViewer\Version9\TeamViewer.exe
InkScape C:\EcosystemApps\inkscape\inkscape.exe
GIMP C:\EcosystemApps\GIMP 2\bin\gimp-2.8.exe

Note that if your login ID is not "Hyrel", you'll need to adjust the location for the Slic3r cfg file appropriately. Remember to click APPLY when done to cause these settings to be applied.

Head & Bed Settings

The latest Head Settings files are available at http://hyrel3d.net/downloads/repetrel/Head_Settings_2019.12.05.rar Note that these are included in the latest v4 Repetrel download.

For Filament-based heads, see the table(s) on our Hot_Flow page.

For Reservoir-based heads, see the table(s) on our Cold_and_Warm_Flow page.

For Hotbeds, we now (v4) have files stored, just like head settings files. If you didn't get them, email me and I'll put the info here.

The names should be self-explanatory:

  • bed_30M_ESR.txt
  • bed_120_hydra.txt
  • bed_200_hydra.txt
  • bed_EHR.txt

Right-click on the head (anywhere EXCEPT the "FLASH" button) and open the proper file for your head or bed:

Loadfromfile1.png

And select the file for the device for which you wish to load the settings:

Loadfromfile2.png

Please note that on some versions, the RTD type is, unfortunately, not populated. For heads, check the pages above.

ESR and 30M units should use "10K".

EHR and 16A units should use "1k PRTD"

As with all settings, to store them as defaults, go to the last page and right-click FLASH:

Rcflash1.png

And then click YES:

Rcflash2.png

Slicer Settings

For Slicer settings, see the Recipes page.