Difference between revisions of "DavidH test"

From Hyrel3D
Jump to navigation Jump to search
Line 330: Line 330:


|}
|}
== new ==

Revision as of 20:47, 11 August 2016

jfjfjh

jhgjhg

Repetrel version 2.855 was released in August, 2015, and is available [here].

jhfg

hjg.jkghbk.hgbkjbj

kgk

new pdf!

The new pdf is at this location

The new pdf is also at [1]


,bkjgkjghk

  • asdlfkjsd
  • a'lskdjfsd
    • asdlkfjsd
    • askdjasdf
  • lakjfsd

table to play with

Settings

Some settings for the EMO-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (1.6mm is default) AND what path width you sliced for. Temperature commands will be ignored by heads with no temperature control. Having said that, here are our default shipping settings:

EMO-Type Head Comparison
Settings EMO, VOL, KRA, COD, VCD, KCD Heads
(17mm Tubes, Various Gear Ratios)
SDS, CSD Heads
(Various Tube Diameters, Standard Gear Ratios)
19:1 Ratio 27:1 Ratio 51:1 Ratio 100:1 Ratio SDS-5 SDS-10 SDS-30 SDS-60
Material
Type Custom Custom Custom Custom Custom Custom Custom Custom
Color (any) (any) (any) (any) (any) (any) (any) (any)
Nozzle 1.600 1.600 1.600 1.600 1.600 1.600 1.600 1.600
Layer 0.300 0.300 0.300 0.300 0.300 0.300 0.300 0.300
Temp Info
Print Temp 35 35 35 35 0 0 0 0
Power Factor 100 100 100 100 100 100 100 100
Minimum 0 0 0 0 0 0 0 0
Maximum 0/100/200 0/100/200 0/100/200 0/100/200 0 0 0 0
Overrides
Pulses 1.600 2.300 4.700 8.500 0.750 0.580* 0.225 0.150
Feed Rate % 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.000
Prime
Please note that Prime values will vary greatly from those shown, depending on the compressibility of your material.
Steps 600 700 1000 4000 200 200 300 500
Rate 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000
Dwell Time (ms) 100 100 110 120 100 100 100 100
Before Tool Change 1 1 1 1 1 1 1 1
Unprime
Please note that Unprime values will vary greatly from those shown, depending on the compressibility of your material.
Steps 500 550 800 3500 160 160 225 400
Rate 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000
Dwell Time (ms) 100 100 100 110 100 100 100 100
After Tool Change 1 1 1 1 1 1 1 1
Offsets
Clone Head Off Off Off Off Off Off Off Off
X 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000
Y 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000
Z 0,000 0,000 0,000 0,000 0,000 0,000 0,000 0,000
Head Info
Model (varies) (varies) (varies) (varies) (varies) (varies) (varies) (varies)
RTD Type 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD 1k PLAT_RTD
Motor Current High High High High High High High High
Step Mode Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth Sixteenth
* Thanks to Yasmine at VT for the precise calculation.

new