DavidH test
jfjfjh
jhgjhg
Repetrel version 2.855 was released in August, 2015, and is available [here].
test
This describes apaskdasdf spf jsdpfj spfj sfj psfj sdlkfjs lfj slfjs dfljsdfff
For more info, see Test.
kgk
new pdf!
The new pdf is at this location
The new pdf is also at [1]
,bkjgkjghk
- asdlfkjsd
- a'lskdjfsd
- asdlkfjsd
- askdjasdf
- lakjfsd
table to play with
Settings
Some settings for the EMO-Type heads (like temperature, prime/unprime values) will vary, depending on what material you are printing with. Nozzle diameter should accurately reflect what nozzle you have loaded (1.6mm is default) AND what path width you sliced for. Temperature commands will be ignored by heads with no temperature control. Having said that, here are our default shipping settings:
| Settings | EMO, VOL, KRA, COD, VCD, KCD Heads (17mm Tubes, Various Gear Ratios) |
SDS, CSD Heads (Various Tube Diameters, Standard Gear Ratios) | ||||||
|---|---|---|---|---|---|---|---|---|
| 19:1 Ratio | 27:1 Ratio | 51:1 Ratio | 100:1 Ratio | SDS-5 | SDS-10 | SDS-30 | SDS-60 | |
| Material | ||||||||
| Type | Custom | Custom | Custom | Custom | Custom | Custom | Custom | Custom |
| Color | (any) | (any) | (any) | (any) | (any) | (any) | (any) | (any) |
| Nozzle | 1.600 | 1.600 | 1.600 | 1.600 | 1.600 | 1.600 | 1.600 | 1.600 |
| Layer | 0.300 | 0.300 | 0.300 | 0.300 | 0.300 | 0.300 | 0.300 | 0.300 |
| Temp Info | ||||||||
| Print Temp | 35 | 35 | 35 | 35 | 0 | 0 | 0 | 0 |
| Power Factor | 100 | 100 | 100 | 100 | 100 | 100 | 100 | 100 |
| Minimum | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 |
| Maximum | 0/100/200 | 0/100/200 | 0/100/200 | 0/100/200 | 0 | 0 | 0 | 0 |
| Overrides | ||||||||
| Pulses | 1.600 | 2.300 | 4.700 | 8.500 | 0.750 | 0.580* | 0.225 | 0.150 |
| Feed Rate % | 1.000 | 1.000 | 1.000 | 1.000 | 1.000 | 1.000 | 1.000 | 1.000 |
| Prime Please note that Prime values will vary greatly from those shown, depending on the compressibility of your material. | ||||||||
| Steps | 600 | 700 | 1000 | 4000 | 200 | 200 | 300 | 500 |
| Rate | 10,000 | 10,000 | 10,000 | 10,000 | 10,000 | 10,000 | 10,000 | 10,000 |
| Dwell Time (ms) | 100 | 100 | 110 | 120 | 100 | 100 | 100 | 100 |
| Before Tool Change | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
| Unprime Please note that Unprime values will vary greatly from those shown, depending on the compressibility of your material. | ||||||||
| Steps | 500 | 550 | 800 | 3500 | 160 | 160 | 225 | 400 |
| Rate | 10,000 | 10,000 | 10,000 | 10,000 | 10,000 | 10,000 | 10,000 | 10,000 |
| Dwell Time (ms) | 100 | 100 | 100 | 110 | 100 | 100 | 100 | 100 |
| After Tool Change | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
| Offsets | ||||||||
| Clone Head | Off | Off | Off | Off | Off | Off | Off | Off |
| X | 0,000 | 0,000 | 0,000 | 0,000 | 0,000 | 0,000 | 0,000 | 0,000 |
| Y | 0,000 | 0,000 | 0,000 | 0,000 | 0,000 | 0,000 | 0,000 | 0,000 |
| Z | 0,000 | 0,000 | 0,000 | 0,000 | 0,000 | 0,000 | 0,000 | 0,000 |
| Head Info | ||||||||
| Model | (varies) | (varies) | (varies) | (varies) | (varies) | (varies) | (varies) | (varies) |
| RTD Type | 1k PLAT_RTD | 1k PLAT_RTD | 1k PLAT_RTD | 1k PLAT_RTD | 1k PLAT_RTD | 1k PLAT_RTD | 1k PLAT_RTD | 1k PLAT_RTD |
| Motor Current | High | High | High | High | High | High | High | High |
| Step Mode | Sixteenth | Sixteenth | Sixteenth | Sixteenth | Sixteenth | Sixteenth | Sixteenth | Sixteenth |
| * Thanks to Yasmine at VT for the precise calculation. | ||||||||
Repetrel 3D Software Printing Basics
Repetrel is a very robust 3D Printing Software developed by Hyrel. Repetrel is a based on the Repetier platform, has embedded Slic3r software, and we provide in-house recipes to optimize your 3D Printing experience. Our research and testing of how different printing variables affect different materials allows us to provide you with a large number of unique Slic3r Recipes to use based on your needs. You can choose the default recipes we provide and recommend, but you can also create custom recipes based on special or complex build requirements, materials, work environment, etc.
The following two pages detail our naming conventions for different Repetrel Screen areas.
The first diagram begins with the basic:
- Main Top Menu Bar
- Left Side Window
- Right Side Window
The second diagram details out more specific items and areas of the Repetrel Software. The Right Side Working Area Window is where you Open STL and GCode files, Select Recipes and Process STL files for Slicing, ultimately generating your GCode file. You also have options for manipulating your 3D Object with regards to size, position and orientation to the build platform. There are more advanced options on the right side where you can view, search, and edit GCode data instructions.